EEPW论坛

按键和IIC有什么区别？

我没看出来。。。。。。

ADC

#include "stm32f10x.h"  
#include "stm32_eval.h"  
#include   
#define VREF 3.3  


/** @addtogroup STM32F10x_StdPeriph_Examples 
  * @{ 
  */  
  
/** @addtogroup EXTI_Config 
  * @{ 
  */   
  
/* Private typedef -----------------------------------------------------------*/  
/* Private define ------------------------------------------------------------*/  
/* Private macro -------------------------------------------------------------*/  
/* Private variables ---------------------------------------------------------*/  
GPIO_InitTypeDef   GPIO_InitStructure;  
USART_InitTypeDef USART_InitStructure;  
USART_ClockInitTypeDef USART_ClockInitStructure;  
unsigned int bule=0,red=0,green=0;  
void RCC_Configuration(void)  
{  
    SystemInit();  
    RCC_APB2PeriphClockCmd(RCC_APB2Periph_GPIOD|RCC_APB2Periph_AFIO, ENABLE);  
    GPIO_PinRemapConfig(GPIO_Remap_SWJ_JTAGDisable,ENABLE);//disable JTAG  
    RCC_APB2PeriphClockCmd(RCC_APB2Periph_GPIOD|RCC_APB2Periph_AFIO, ENABLE);  
    GPIO_PinRemapConfig(GPIO_Remap_SWJ_JTAGDisable,ENABLE);//disable JTAG  
    GPIO_InitStructure.GPIO_Pin = GPIO_Pin_2;  
    GPIO_InitStructure.GPIO_Speed = GPIO_Speed_50MHz;  
    GPIO_InitStructure.GPIO_Mode = GPIO_Mode_Out_PP;  
    GPIO_Init(GPIOD, &GPIO_InitStructure);  
    GPIO_ResetBits(GPIOD,GPIO_Pin_2);  
    RCC_APB2PeriphClockCmd(RCC_APB2Periph_GPIOC|RCC_APB2Periph_AFIO, ENABLE);  
    GPIO_PinRemapConfig(GPIO_Remap_SWJ_JTAGDisable,ENABLE);//disable JTAG  
    GPIO_InitStructure.GPIO_Pin = GPIO_Pin_0|GPIO_Pin_1|GPIO_Pin_2|GPIO_Pin_3|GPIO_Pin_4|GPIO_Pin_5|GPIO_Pin_6|GPIO_Pin_7;  
    GPIO_InitStructure.GPIO_Speed = GPIO_Speed_50MHz;  
    GPIO_InitStructure.GPIO_Mode = GPIO_Mode_Out_PP;  
    GPIO_Init(GPIOC, &GPIO_InitStructure);  
    GPIO_SetBits(GPIOC,GPIO_Pin_0|GPIO_Pin_1|GPIO_Pin_2|GPIO_Pin_3|GPIO_Pin_4|GPIO_Pin_5|GPIO_Pin_6|GPIO_Pin_7);  
    RCC_APB1PeriphClockCmd(RCC_APB1Periph_TIM2, ENABLE);  
}   
  
void USART_int(long BaudRate)  
{  
    RCC_APB2PeriphClockCmd(RCC_APB2Periph_GPIOA|RCC_APB2Periph_USART1,ENABLE);  
    GPIO_InitStructure.GPIO_Pin = GPIO_Pin_9;  
    GPIO_InitStructure.GPIO_Speed = GPIO_Speed_50MHz;  
    GPIO_InitStructure.GPIO_Mode = GPIO_Mode_AF_PP;   
    GPIO_Init(GPIOA, &GPIO_InitStructure);  
    /* PA10 USART1_Rx  */  
    GPIO_InitStructure.GPIO_Pin = GPIO_Pin_10;  
    GPIO_InitStructure.GPIO_Mode = GPIO_Mode_IN_FLOATING;  
    GPIO_Init(GPIOA, &GPIO_InitStructure);  
  /* USARTx configured as follow: 
        - BaudRate = 115200 baud   
        - Word Length = 8 Bits 
        - One Stop Bit 
        - No parity 
        - Hardware flow control disabled (RTS and CTS signals) 
        - Receive and transmit enabled 
  */  
  USART_InitStructure.USART_BaudRate = BaudRate;//??????  
  USART_InitStructure.USART_WordLength = USART_WordLength_8b;//???????8bit  
  USART_InitStructure.USART_StopBits = USART_StopBits_1;//????1  
  USART_InitStructure.USART_Parity = USART_Parity_No;//????  
  USART_InitStructure.USART_HardwareFlowControl = USART_HardwareFlowControl_None;//??????none  
  USART_InitStructure.USART_Mode = USART_Mode_Rx | USART_Mode_Tx;//??????????  
  USART_ClockInitStructure.USART_Clock = USART_Clock_Disable;       
  USART_ClockInitStructure.USART_CPOL = USART_CPOL_Low;        
  USART_ClockInitStructure.USART_CPHA = USART_CPHA_2Edge;        
  USART_ClockInitStructure.USART_LastBit = USART_LastBit_Disable;  
  USART_ClockInit(USART1, &USART_ClockInitStructure);  
  USART_Init(USART1, &USART_InitStructure);  
  USART_Cmd(USART1, ENABLE);  
  USART_ITConfig(USART1, USART_IT_RXNE, ENABLE);  
  USART_Cmd(USART1, ENABLE);  
}  
  
  
void PWM_Config()  
{  
  uint16_t PrescalerValue = 0;  
  TIM_TimeBaseInitTypeDef  TIM_TimeBaseStructure;  
  TIM_OCInitTypeDef  TIM_OCInitStructure;  
  /* TIM2 clock enable */  
  RCC_APB1PeriphClockCmd(RCC_APB1Periph_TIM2, ENABLE);  
  /* GPIOA  enable */  
  RCC_APB2PeriphClockCmd(RCC_APB2Periph_AFIO  , ENABLE);  
      
  GPIO_InitStructure.GPIO_Pin = GPIO_Pin_1|GPIO_Pin_2|GPIO_Pin_3;  
  GPIO_InitStructure.GPIO_Mode = GPIO_Mode_AF_PP;  
  GPIO_InitStructure.GPIO_Speed = GPIO_Speed_50MHz;  
  GPIO_Init(GPIOA, &GPIO_InitStructure);  
  TIM_Cmd(TIM2, ENABLE);  
  /* Compute the prescaler value */  
  PrescalerValue = (uint16_t) (SystemCoreClock / 24000000) - 1;  
  /* Time base configuration */  
  TIM_TimeBaseStructure.TIM_Period = 0x07FF;  
  TIM_TimeBaseStructure.TIM_Prescaler = PrescalerValue;  
  TIM_TimeBaseStructure.TIM_ClockDivision = 0;  
  TIM_TimeBaseStructure.TIM_CounterMode = TIM_CounterMode_Up;  
  TIM_TimeBaseInit(TIM2, &TIM_TimeBaseStructure);  
  TIM_OCInitStructure.TIM_OCMode = TIM_OCMode_PWM1;  
  TIM_OCInitStructure.TIM_OCPolarity = TIM_OCPolarity_High;  
  /* PWM1 Mode configuration: Channel2 */  
  TIM_OCInitStructure.TIM_OutputState = TIM_OutputState_Enable;  
  TIM_OCInitStructure.TIM_Pulse = 0xFFFF;  
  TIM_OC2Init(TIM2, &TIM_OCInitStructure);  
  /* PWM1 Mode configuration: Channel3 */  
  TIM_OCInitStructure.TIM_OutputState = TIM_OutputState_Enable;  
  TIM_OCInitStructure.TIM_Pulse = 0xFFFF;  
  TIM_OC3Init(TIM2, &TIM_OCInitStructure);  
  /* PWM1 Mode configuration: Channel4 */  
  TIM_OCInitStructure.TIM_OutputState = TIM_OutputState_Enable;  
  TIM_OCInitStructure.TIM_Pulse = 0xFFFF;  
  TIM_OC4Init(TIM2, &TIM_OCInitStructure);  
  TIM_ARRPreloadConfig(TIM2, ENABLE);  
}  
  
void ADC_CONFIG(){  
  ADC_InitTypeDef ADC_InitStructure;  
#if defined (STM32F10X_LD_VL) || defined (STM32F10X_MD_VL) || defined (STM32F10X_HD_VL)  
  /* ADCCLK = PCLK2/2 */  
  RCC_ADCCLKConfig(RCC_PCLK2_Div2);   
#else  
  /* ADCCLK = PCLK2/4 */  
  RCC_ADCCLKConfig(RCC_PCLK2_Div4);   
#endif  
  ADC_DeInit(ADC1);  
  /* Enable ADC1 and GPIOC clock */  
  RCC_APB2PeriphClockCmd(RCC_APB2Periph_ADC1 | RCC_APB2Periph_GPIOB, ENABLE);  
      
    /* Configure PB0 (ADC Channel14) as analog input -------------------------*/  
  GPIO_InitStructure.GPIO_Pin = GPIO_Pin_0;  
  GPIO_InitStructure.GPIO_Mode = GPIO_Mode_AIN;  
  GPIO_Init(GPIOB, &GPIO_InitStructure);  
      
    
  /* ADC1 configuration ------------------------------------------------------*/  
  ADC_InitStructure.ADC_Mode = ADC_Mode_Independent;  
  ADC_InitStructure.ADC_ScanConvMode = ENABLE;  
  ADC_InitStructure.ADC_ContinuousConvMode = ENABLE;  
  ADC_InitStructure.ADC_ExternalTrigConv = ADC_ExternalTrigConv_None;  
  ADC_InitStructure.ADC_DataAlign = ADC_DataAlign_Right;//ADC?????  
  ADC_InitStructure.ADC_NbrOfChannel = 1;//ADC???1  
  ADC_Init(ADC1, &ADC_InitStructure);  
  
  
  /* Enable ADC1 DMA */  
  ADC_DMACmd(ADC1, ENABLE);  
    
  /* Enable ADC1 */  
  ADC_Cmd(ADC1, ENABLE);  
  
}  
  
int Get_ADC(){  
  /* ADC1 regular channel configuration */   
  ADC_RegularChannelConfig(ADC1, ADC_Channel_8, 1, ADC_SampleTime_55Cycles5);//??8,????  
  /* Enable ADC1 reset calibration register */     
  ADC_ResetCalibration(ADC1);  
  /* Check the end of ADC1 reset calibration register */  
  while(ADC_GetResetCalibrationStatus(ADC1));//??ADC??????  
  /* Start ADC1 calibration */  
  ADC_StartCalibration(ADC1);//??ADC??  
  /* Check the end of ADC1 calibration */  
  while(ADC_GetCalibrationStatus(ADC1));//??ADC??????     
  /* Start ADC1 Software Conversion */   
  ADC_SoftwareStartConvCmd(ADC1, ENABLE);  
      
    return ADC_GetConversionValue(ADC1);  
}  
  
 void delay_us(u32 n)  
{  
    u8 j;  
    while(n--)  
    for(j=0;j<10;j++);  
}  
  
void  delay_ms(u32 n)  
{  
    while(n--)  
    delay_us(1000);  
} 
  
void PWM_TEST()  
{  
//  printf("PWM-RGB TEST......\r\n");     
        TIM_SetCompare2(TIM2, bule);  
        TIM_SetCompare3(TIM2, red);  
        TIM_SetCompare4(TIM2, green);  
//      delay_ms(500);  
}  
  
  
  
/* Private functions ---------------------------------------------------------*/  
  
/** 
  * @brief  Main program. 
  * @param  None 
  * @retval None 
  */  
int main(void)  
{  
    float Volt=0.00;  
    int ADValue = 0;  
  /*!< At this stage the microcontroller clock setting is already configured,  
       this is done through SystemInit() function which is called from startup 
       file (startup_stm32f10x_xx.s) before to branch to application main. 
       To reconfigure the default setting of SystemInit() function, refer to 
       system_stm32f10x.c file 
     */       
         
  /* System Clocks Configuration */  
  RCC_Configuration();  
  USART_int(115200);  
  ADC_CONFIG();  
  printf(" config done...\r\n");  
  Get_ADC();  
  PWM_Config();  
  delay_ms(1000);  
  while(1)  
    {     
        ADValue = Get_ADC();  
        Volt = VREF*ADValue/4095;  
        if(03000)  
        {  
            bule=ADValue/1;  
            red=ADValue/1;  
            green=ADValue/1;  
        }  
        PWM_TEST();  
        printf("The ADC value is :%d\r\n",ADValue);  
        printf("The Volt is:%f V\r\n",Volt);  
      delay_ms(100);  
    }  
}  
  
  
  
#ifdef  USE_FULL_ASSERT  
  
/** 
  * @brief  Reports the name of the source file and the source line number 
  *         where the assert_param error has occurred. 
  * @param  file: pointer to the source file name 
  * @param  line: assert_param error line source number 
  * @retval None 
  */  
void assert_failed(uint8_t* file, uint32_t line)  
{   
  /* User can add his own implementation to report the file name and line number, 
     ex: printf("Wrong parameters value: file %s on line %d\r\n", file, line) */  
  
  /* Infinite loop */  
  while (1)  
  {  
  }  
}  
  
#endif  
  
/** 
  * @} 
  */   
  
/** 
  * @} 
  */   
  
#ifdef __GNUC__  
  /* With GCC/RAISONANCE, small printf (option LD Linker->Libraries->Small printf 
     set to 'Yes') calls __io_putchar() */  
  #define PUTCHAR_PROTOTYPE int __io_putchar(int ch)  
#else  
  #define PUTCHAR_PROTOTYPE int fputc(int ch, FILE *f)  
#endif /* __GNUC__ */  
    
  
  
/** 
  * @brief  Retargets the C library printf function to the USART. 
  * @param  None 
  * @retval None 
  */  
PUTCHAR_PROTOTYPE  
{  
  /* Place your implementation of fputc here */  
  /* e.g. write a character to the USART */  
  USART_SendData(EVAL_COM1, (uint8_t) ch);  
  
  /* Loop until the end of transmission */  
  while (USART_GetFlagStatus(EVAL_COM1, USART_FLAG_TC) == RESET)  
  {}  
  
  return ch;  
}  
  
#ifdef  USE_FULL_ASSERT  
  
/** 
  * @brief  Reports the name of the source file and the source line number 
  *         where the assert_param error has occurred. 
  * @param  file: pointer to the source file name 
  * @param  line: assert_param error line source number 
  * @retval None 
  */  
void assert_failed(uint8_t* file, uint32_t line)  
{   
  /* User can add his own implementation to report the file name and line number, 
     ex: printf("Wrong parameters value: file %s on line %d\r\n", file, line) */  
  
  /* Infinite loop */  
  while (1)  
  {  
  }  
}  
  
#endif 

#include "stm32f10x.h"     
#include "stm32_eval.h"     
GPIO_InitTypeDef GPIO_InitStructure;    //??GPIO???  
  
NVIC_InitTypeDef  NVIC_InitStructure;  
USART_InitTypeDef  USART_InitStructure;   
USART_ClockInitTypeDef  USART_ClockInitStructure;   
  
#define buff_size  16;       
char rx_buff[],rx_buff_count=0;  
  
/*???? ??*/    
void delay_us(u32 n)     
{     
    u8 j;     
    while(n--)     
    for(j=0;j<10;j++);     
}     
/*???? ??*/    
void  delay_ms(u32 n)     
{     
   while(n--)     
    delay_us(1000);     
}   
  
void RCC_Configuration(void)     
{     
    RCC_DeInit();     
    RCC_HSICmd(ENABLE);     
    while(RCC_GetFlagStatus(RCC_FLAG_HSIRDY) == RESET);     
    RCC_SYSCLKConfig(RCC_SYSCLKSource_HSI);     
    RCC_HSEConfig(RCC_HSE_OFF);     
    RCC_LSEConfig(RCC_LSE_OFF);     
    RCC_PLLConfig(RCC_PLLSource_HSI_Div2,RCC_PLLMul_9); //  72HMz     
    RCC_PLLCmd(ENABLE);     
    while(RCC_GetFlagStatus(RCC_FLAG_PLLRDY) == RESET);     
    RCC_ADCCLKConfig(RCC_PCLK2_Div4);     
    RCC_PCLK2Config(RCC_HCLK_Div1);     
    RCC_PCLK1Config(RCC_HCLK_Div2);     
    RCC_HCLKConfig(RCC_SYSCLK_Div1);     
    RCC_SYSCLKConfig(RCC_SYSCLKSource_PLLCLK);     
    while(RCC_GetSYSCLKSource() != 0x08);     
    RCC_APB2PeriphClockCmd(RCC_APB2Periph_GPIOD|RCC_APB2Periph_AFIO, ENABLE);     
    GPIO_PinRemapConfig(GPIO_Remap_SWJ_JTAGDisable,ENABLE);  
    GPIO_InitStructure.GPIO_Pin = GPIO_Pin_2;     
    GPIO_InitStructure.GPIO_Speed = GPIO_Speed_50MHz;     
    GPIO_InitStructure.GPIO_Mode = GPIO_Mode_Out_PP;     
    GPIO_Init(GPIOD, &GPIO_InitStructure);     
    GPIO_ResetBits(GPIOD,GPIO_Pin_2);                      //?????  
}   
  
void USART_SendStr(char *str)      //???????  
{  
   while((*str)!='\0')             //???????  
        {USART_SendData(USART1,*str++);  
        while(USART_GetFlagStatus(USART1, USART_FLAG_TXE) == RESET);  
        }  
}  
  
void USART_int(long BaudRate)       //USART??  
{  
      RCC_APB2PeriphClockCmd(RCC_APB2Periph_GPIOA|RCC_APB2Periph_USART1,ENABLE);//??PA?USART1  
    GPIO_InitStructure.GPIO_Pin = GPIO_Pin_9;               //PA^9??TX_D1  
    GPIO_InitStructure.GPIO_Speed = GPIO_Speed_10MHz;  
    GPIO_InitStructure.GPIO_Mode = GPIO_Mode_AF_PP;          //??????  
    GPIO_Init(GPIOA, &GPIO_InitStructure);  
    GPIO_InitStructure.GPIO_Pin = GPIO_Pin_10;               //PA^10??RX_D1  
    GPIO_InitStructure.GPIO_Mode = GPIO_Mode_IN_FLOATING;     //????  
    GPIO_Init(GPIOA, &GPIO_InitStructure);  
  
    USART_InitStructure.USART_BaudRate = BaudRate;//????  
    USART_InitStructure.USART_WordLength = USART_WordLength_8b;//??8bit  
    USART_InitStructure.USART_StopBits = USART_StopBits_1;      //???1  
    USART_InitStructure.USART_Parity = USART_Parity_No;//????  
    USART_InitStructure.USART_HardwareFlowControl = USART_HardwareFlowControl_None;  //???none  
    USART_InitStructure.USART_Mode = USART_Mode_Rx | USART_Mode_Tx;                  //???????  
      USART_ClockInitStructure.USART_Clock = USART_Clock_Disable;       
    USART_ClockInitStructure.USART_CPOL = USART_CPOL_Low;        
    USART_ClockInitStructure.USART_CPHA = USART_CPHA_2Edge;        
    USART_ClockInitStructure.USART_LastBit = USART_LastBit_Disable;  
    USART_ClockInit(USART1, &USART_ClockInitStructure);           //???USART1??       
    USART_Init(USART1, &USART_InitStructure);                    //???USART1  
    USART_Cmd(USART1, ENABLE);   
      USART_ITConfig(USART1, USART_IT_RXNE, ENABLE);  
    USART_Cmd(USART1, ENABLE);  
   
        NVIC_PriorityGroupConfig(NVIC_PriorityGroup_4);       //??4????  
        NVIC_InitStructure.NVIC_IRQChannel = USART1_IRQn;     //??USART1????  
        NVIC_InitStructure.NVIC_IRQChannelPreemptionPriority = 15;  
        NVIC_InitStructure.NVIC_IRQChannelCmd = ENABLE;  
        NVIC_Init(&NVIC_InitStructure);                       //?????  
}  
  
void GPIO_INIT()     
{    
    RCC_APB2PeriphClockCmd(RCC_APB2Periph_GPIOC, ENABLE);  //RCC_APB2Periph_GPIOC  ??GPIOX???      ENABLE\DISABLE   ??or??    
    GPIO_InitStructure.GPIO_Pin = GPIO_Pin_0|GPIO_Pin_1|GPIO_Pin_2|GPIO_Pin_3|GPIO_Pin_4|GPIO_Pin_5|GPIO_Pin_6|GPIO_Pin_7;//??:????PC^0-7     
    GPIO_InitStructure.GPIO_Speed = GPIO_Speed_50MHz;         //??:????  
    GPIO_InitStructure.GPIO_Mode = GPIO_Mode_Out_PP;          //??:Out_PP????,????,??         
    GPIO_Init(GPIOC, &GPIO_InitStructure);    
}  
  
unsigned int my_atoi(char* pstr) //???:????????  
{     
      int s = 0;    
        while(*pstr != '\0')        //??????????????  
        {  
                if(*pstr >= '0' && *pstr <= '9')  //????????0-9???  
                {    
                        s = s * 10 + *pstr - '0';     
                }    
                pstr++;  
        }         
    return s;   
}   
  
  
  
  
  
int main()    
{                             
        RCC_Configuration();  
      GPIO_INIT();   
        USART_int(9600);  
        USART_SendStr("Please input like: data=\r\n");  
        USART_SendStr("\n>");  
        while(1){  
                }  
}  
  
void USART1_IRQHandler(void)   
{   
  while(USART_GetFlagStatus(USART1, USART_FLAG_RXNE) == RESET)  
  {   
  }   
      
  USART_ClearFlag(USART1, USART_FLAG_RXNE);  
  
}

#include "stm32f10x.h"

#include "stm32_eval.h"

#include 
void delay_us(u32 n)     
{     
    u8 j;     
    while(n--)     
    for(j=0;j<10;j++);     
}     
  
void  delay_ms(u32 n)     
{     
    while(n--)     
    delay_us(1000);     
}

volatile int flag;
#define Set_B20()	 GPIO_SetBits(GPIOC, GPIO_Pin_12)
#define Reset_B20()	 GPIO_ResetBits(GPIOC, GPIO_Pin_12)
#define Read_B20()	 GPIO_ReadInputDataBit(GPIOC,GPIO_Pin_12)
unsigned char Error_Flag=0;
unsigned char zf=0;
void SysTick_Configuration(void)
{
  /* Setup SysTick Timer for 10 msec interrupts  */
  if (SysTick_Config(48000))                //SysTick??
  { 
    /* Capture error */ 
    while (1);
  }  
 /* Configure the SysTick handler priority */
  NVIC_SetPriority(SysTick_IRQn, 0x0);                       //SysTick?????
}


/** @addtogroup STM32F10x_StdPeriph_Examples
  * @{
  */

/** @addtogroup EXTI_Config
  * @{
  */ 

/* Private typedef -----------------------------------------------------------*/
/* Private define ------------------------------------------------------------*/
/* Private macro -------------------------------------------------------------*/
/* Private variables ---------------------------------------------------------*/
GPIO_InitTypeDef   GPIO_InitStructure;
USART_InitTypeDef USART_InitStructure;
USART_ClockInitTypeDef USART_ClockInitStructure;

void RCC_Configuration(void)
{
  RCC_DeInit();
    
  RCC_HSICmd(ENABLE);
  while(RCC_GetFlagStatus(RCC_FLAG_HSIRDY) == RESET);
  
  RCC_SYSCLKConfig(RCC_SYSCLKSource_HSI);
  
  RCC_HSEConfig(RCC_HSE_OFF);
  RCC_LSEConfig(RCC_LSE_OFF);
  RCC_PLLConfig(RCC_PLLSource_HSI_Div2,RCC_PLLMul_12); //  72HMz
  RCC_PLLCmd(ENABLE);
  while(RCC_GetFlagStatus(RCC_FLAG_PLLRDY) == RESET);
  RCC_ADCCLKConfig(RCC_PCLK2_Div4);
  RCC_PCLK2Config(RCC_HCLK_Div1);
  RCC_PCLK1Config(RCC_HCLK_Div2);
  RCC_HCLKConfig(RCC_SYSCLK_Div1);
  RCC_SYSCLKConfig(RCC_SYSCLKSource_PLLCLK);
  while(RCC_GetSYSCLKSource() != 0x08);

	
//	SystemInit();
	
	RCC_APB2PeriphClockCmd(RCC_APB2Periph_GPIOD|RCC_APB2Periph_AFIO, ENABLE);
 GPIO_PinRemapConfig(GPIO_Remap_SWJ_JTAGDisable,ENABLE);//disable JTAG
RCC_APB2PeriphClockCmd(RCC_APB2Periph_GPIOD|RCC_APB2Periph_AFIO, ENABLE);
 GPIO_PinRemapConfig(GPIO_Remap_SWJ_JTAGDisable,ENABLE);//disable JTAG
  GPIO_InitStructure.GPIO_Pin = GPIO_Pin_2;
  GPIO_InitStructure.GPIO_Speed = GPIO_Speed_50MHz;
  GPIO_InitStructure.GPIO_Mode = GPIO_Mode_Out_PP;
  GPIO_Init(GPIOD, &GPIO_InitStructure);
	GPIO_ResetBits(GPIOD,GPIO_Pin_2);
	RCC_APB2PeriphClockCmd(RCC_APB2Periph_GPIOC|RCC_APB2Periph_AFIO, ENABLE);
 GPIO_PinRemapConfig(GPIO_Remap_SWJ_JTAGDisable,ENABLE);//disable JTAG
  GPIO_InitStructure.GPIO_Pin = GPIO_Pin_0|GPIO_Pin_1|GPIO_Pin_2|GPIO_Pin_3|GPIO_Pin_4|GPIO_Pin_5|GPIO_Pin_6|GPIO_Pin_7;
  GPIO_InitStructure.GPIO_Speed = GPIO_Speed_50MHz;
  GPIO_InitStructure.GPIO_Mode = GPIO_Mode_Out_PP;
  GPIO_Init(GPIOC, &GPIO_InitStructure);
	GPIO_SetBits(GPIOC,GPIO_Pin_0|GPIO_Pin_1|GPIO_Pin_2|GPIO_Pin_3|GPIO_Pin_4|GPIO_Pin_5|GPIO_Pin_6|GPIO_Pin_7);
	  RCC_APB1PeriphClockCmd(RCC_APB1Periph_TIM2, ENABLE);
} 

void USART_int(long BaudRate)
{
	RCC_APB2PeriphClockCmd(RCC_APB2Periph_GPIOA|RCC_APB2Periph_USART1,ENABLE);
       GPIO_InitStructure.GPIO_Pin = GPIO_Pin_9;
    GPIO_InitStructure.GPIO_Speed = GPIO_Speed_50MHz;
    GPIO_InitStructure.GPIO_Mode = GPIO_Mode_AF_PP; 
    GPIO_Init(GPIOA, &GPIO_InitStructure);
    /* PA10 USART1_Rx  */
    GPIO_InitStructure.GPIO_Pin = GPIO_Pin_10;
    GPIO_InitStructure.GPIO_Mode = GPIO_Mode_IN_FLOATING;
    GPIO_Init(GPIOA, &GPIO_InitStructure);
  /* USARTx configured as follow:
        - BaudRate = 115200 baud  
        - Word Length = 8 Bits
        - One Stop Bit
        - No parity
        - Hardware flow control disabled (RTS and CTS signals)
        - Receive and transmit enabled
  */
  USART_InitStructure.USART_BaudRate = BaudRate;//??????
  USART_InitStructure.USART_WordLength = USART_WordLength_8b;//???????8bit
  USART_InitStructure.USART_StopBits = USART_StopBits_1;//????1
  USART_InitStructure.USART_Parity = USART_Parity_No;//????
  USART_InitStructure.USART_HardwareFlowControl = USART_HardwareFlowControl_None;//??????none
  USART_InitStructure.USART_Mode = USART_Mode_Rx | USART_Mode_Tx;//??????????
	USART_ClockInitStructure.USART_Clock = USART_Clock_Disable;     
    USART_ClockInitStructure.USART_CPOL = USART_CPOL_Low;      
    USART_ClockInitStructure.USART_CPHA = USART_CPHA_2Edge;      
    USART_ClockInitStructure.USART_LastBit = USART_LastBit_Disable;
    USART_ClockInit(USART1, &USART_ClockInitStructure);
  USART_Init(USART1, &USART_InitStructure);
  USART_Cmd(USART1, ENABLE);
	USART_ITConfig(USART1, USART_IT_RXNE, ENABLE);
 USART_Cmd(USART1, ENABLE);
}

void delay_18b20(u32 nus)
{
	u16 i;
	while(nus--)
		for(i=12;i>0;i--);
}


	
void Init18B20(void)
{
   u8 aa=0;
   u8 count =0;
	RCC_APB2PeriphClockCmd(RCC_APB2Periph_GPIOC, ENABLE);
  GPIO_InitStructure.GPIO_Pin = GPIO_Pin_12;
  GPIO_InitStructure.GPIO_Mode = GPIO_Mode_Out_OD;
  GPIO_Init(GPIOC, &GPIO_InitStructure);
   Set_B20() ;
   delay_18b20(1);
   Reset_B20();

   delay_18b20(480);
   Set_B20();
//	delay_18b20(500);
   delay_18b20(480);

	count=0;
	aa=Read_B20();
    while(!aa && count<100)	 
   {
   	aa=Read_B20();
	count++;
   }
   if(count>=99)
   		Error_Flag=1;
	else
		Error_Flag=0;
   
}
  
unsigned char Read18B20(void)
{  
unsigned char i=0;
unsigned char date=0;
u8 tempp;
   for(i=8;i>0;i--)
   {

   Reset_B20();
   date>>=1;
   delay_18b20(1);
   Set_B20(); 
    delay_18b20(1);
   tempp=Read_B20();

   if(tempp)
   		date|=0x80; 
	delay_18b20(60);
	}
	return(date);
}
void Write18B20(unsigned char date)
{
	unsigned char i=0;

	for (i=8; i>0; i--)
	{
		Reset_B20(); 
		delay_18b20(1); 		
		if(date & 0x01)			
		{	
			Set_B20();
		}
		else
		{	Reset_B20();}
		delay_18b20(60);
		date>>=1; 	 
		 Set_B20();
		 delay_18b20(1);
			
	}
	delay_18b20(15);
}

 float Read_T()
{	
		unsigned char TUp,TDown;
	unsigned char fTemp;
	u8 TT=0;

	 float Temp = 0;
	Init18B20();
	Write18B20(0xcc); 	  
	Write18B20(0x44); 	 
	Init18B20();
	Write18B20(0xcc); 	
	Write18B20(0xbe); 	
	TDown = Read18B20();   	
	TUp = Read18B20();   	
	
	if(TUp>0x7f)      
	{
		TDown=~TDown;  
		TUp=~TUp+1; 
		TUp/=8;		     
		zf=1;         
 	}
	else
		zf=0;	  

	fTemp=TDown&0x0f;		
	TUp<<=4;
	TDown>>=4;
	TT=TUp|TDown;
	Temp=TT+(float)fTemp/16;		
	return(Temp);
}
                                 
int main(void)
{
		
  /*!< At this stage the microcontroller clock setting is already configured, 
       this is done through SystemInit() function which is called from startup
       file (startup_stm32f10x_xx.s) before to branch to application main.
       To reconfigure the default setting of SystemInit() function, refer to
       system_stm32f10x.c file
     */     
       
  /* System Clocks Configuration */
 int i; 
 int ID[8];
  RCC_Configuration();  
  USART_int(115200);
  
    SysTick_Configuration();  
    Init18B20();                //18B20³õʼ»¯ 
    printf(" config done...\r\n");
	Write18B20(0x33);     //  
  for(i=0;i<8;i++)    
  {    
        ID[i]=Read18B20();   //¶ÁÈ¡18b20ID·Åµ½Êý×éÖÐ   
  }    
   delay_ms(1000); 
	  while(1) 
		{ 			
			flag++;  
        if(flag==300)   //300ms¶ÁÒ»´ÎID 
        {   
            printf("The ID is:\n");  
             for(i=0;i<8;i++)    
        {    
            printf("%u",ID[i]);    
        }   
				
    }  
        printf("\n");   
        if(flag == 500)     //500ms¶ÁÒ»´ÎÎÂ¶È  
				{
					printf("The Temperature is:%f\r\n",Read_T());//????   
          flag=0;   
         }  
    }			
			  
}




#ifdef  USE_FULL_ASSERT

/**
  * @brief  Reports the name of the source file and the source line number
  *         where the assert_param error has occurred.
  * @param  file: pointer to the source file name
  * @param  line: assert_param error line source number
  * @retval None
  */
void assert_failed(uint8_t* file, uint32_t line)
{ 
  /* User can add his own implementation to report the file name and line number,
     ex: printf("Wrong parameters value: file %s on line %d\r\n", file, line) */

  /* Infinite loop */
  while (1)
  {
  }
}

#endif

/**
  * @}
  */ 

/**
  * @}
  */ 

#ifdef __GNUC__
  /* With GCC/RAISONANCE, small printf (option LD Linker->Libraries->Small printf
     set to 'Yes') calls __io_putchar() */
  #define PUTCHAR_PROTOTYPE int __io_putchar(int ch)
#else
  #define PUTCHAR_PROTOTYPE int fputc(int ch, FILE *f)
#endif /* __GNUC__ */
  


/**
  * @brief  Retargets the C library printf function to the USART.
  * @param  None
  * @retval None
  */
PUTCHAR_PROTOTYPE
{
  /* Place your implementation of fputc here */
  /* e.g. write a character to the USART */
  USART_SendData(EVAL_COM1, (uint8_t) ch);

  /* Loop until the end of transmission */
  while (USART_GetFlagStatus(EVAL_COM1, USART_FLAG_TC) == RESET)
  {}

  return ch;
}

#ifdef  USE_FULL_ASSERT

/**
  * @brief  Reports the name of the source file and the source line number
  *         where the assert_param error has occurred.
  * @param  file: pointer to the source file name
  * @param  line: assert_param error line source number
  * @retval None
  */
void assert_failed(uint8_t* file, uint32_t line)
{ 
  /* User can add his own implementation to report the file name and line number,
     ex: printf("Wrong parameters value: file %s on line %d\r\n", file, line) */

  /* Infinite loop */
  while (1)
  {
  }
}

#endif

/******************* (C) COPYRIGHT 2011 STMicroelectronics *****END OF FILE****/

#include "stm32f10x.h"  
#include "stm32_eval.h"  
#include <stdio.h>  
#include "spi_flash.h"  
#define VREF 3.3  
  
void delay_us(u32 n)  
{  
    u8 j;  
    while(n--)  
    for(j=0;j<10;j++);  
}  
  
void  delay_ms(u32 n)  
{  
    while(n--)  
    delay_us(1000);  
}  
  
  
#define TxBufferSize1   (countof(TxBuffer1) - 1)  
#define RxBufferSize1   (countof(TxBuffer1) - 1)  
#define countof(a)      (sizeof(a) / sizeof(*(a)))  
#define  BufferSize (countof(Tx_Buffer)-1)  
typedef enum { FAILED = 0, PASSED = !FAILED} TestStatus;  
#define  FLASH_WriteAddress     0x00000  
#define  FLASH_ReadAddress      FLASH_WriteAddress  
#define  FLASH_SectorToErase    FLASH_WriteAddress  
#define  sFLASH_ID              0xEF3015     //W25X16  
//#define  sFLASH_ID              0xEF4015   //W25Q16  
#define buff_size  16;       
char rx_buff[],rx_buff_count=0;  
/* ???????? */  
uint8_t Tx_Buffer[4096] ;  
uint8_t Rx_Buffer[BufferSize];  
__IO uint32_t DeviceID = 0;  
__IO uint32_t FlashID = 0;  
__IO TestStatus TransferStatus1 = FAILED;  
  
// ??????  
void Delay(__IO uint32_t nCount);  
TestStatus Buffercmp(uint8_t* pBuffer1, uint8_t* pBuffer2, uint16_t BufferLength);  
  
/** @addtogroup STM32F10x_StdPeriph_Examples 
  * @{ 
  */  
  
/** @addtogroup EXTI_Config 
  * @{ 
  */   
  
/* Private typedef -----------------------------------------------------------*/  
/* Private define ------------------------------------------------------------*/  
/* Private macro -------------------------------------------------------------*/  
/* Private variables ---------------------------------------------------------*/  
GPIO_InitTypeDef   GPIO_InitStructure;  
USART_InitTypeDef USART_InitStructure;  
USART_ClockInitTypeDef USART_ClockInitStructure;  
  
char *int_to_string(int number,char *strnum)//整形数据转换为字符型  
{  
int j=0,i=0,n=0;  
char temp;  
while(number>0)  
{  
*(strnum+j)=number%10+48;  
j++;  
number=number/10;  
n++;  
}  
  
      
for(i=0;i<n/2;i++)  
{  
temp=*(strnum+j+i-n);  
*(strnum+j+i-n)=*(strnum+j-i-1);  
*(strnum+j-i-1)=temp;  
}  
strnum[n]='\0';  
return strnum;  
}  
  
void RCC_Configuration(void)  
{  
  RCC_DeInit();  
      
  RCC_HSICmd(ENABLE);  
  while(RCC_GetFlagStatus(RCC_FLAG_HSIRDY) == RESET);  
    
  RCC_SYSCLKConfig(RCC_SYSCLKSource_HSI);  
    
  RCC_HSEConfig(RCC_HSE_OFF);  
  RCC_LSEConfig(RCC_LSE_OFF);  
  RCC_PLLConfig(RCC_PLLSource_HSI_Div2,RCC_PLLMul_9); //  72HMz  
  RCC_PLLCmd(ENABLE);  
  while(RCC_GetFlagStatus(RCC_FLAG_PLLRDY) == RESET);  
  RCC_ADCCLKConfig(RCC_PCLK2_Div4);  
  RCC_PCLK2Config(RCC_HCLK_Div1);  
  RCC_PCLK1Config(RCC_HCLK_Div2);  
  RCC_HCLKConfig(RCC_SYSCLK_Div1);  
  RCC_SYSCLKConfig(RCC_SYSCLKSource_PLLCLK);  
  while(RCC_GetSYSCLKSource() != 0x08);  
  
      
    //SystemInit();  
      
    RCC_APB2PeriphClockCmd(RCC_APB2Periph_GPIOD|RCC_APB2Periph_AFIO, ENABLE);  
 GPIO_PinRemapConfig(GPIO_Remap_SWJ_JTAGDisable,ENABLE);//disable JTAG  
RCC_APB2PeriphClockCmd(RCC_APB2Periph_GPIOD|RCC_APB2Periph_AFIO, ENABLE);  
 GPIO_PinRemapConfig(GPIO_Remap_SWJ_JTAGDisable,ENABLE);//disable JTAG  
  GPIO_InitStructure.GPIO_Pin = GPIO_Pin_2;  
  GPIO_InitStructure.GPIO_Speed = GPIO_Speed_50MHz;  
  GPIO_InitStructure.GPIO_Mode = GPIO_Mode_Out_PP;  
  GPIO_Init(GPIOD, &GPIO_InitStructure);  
    GPIO_ResetBits(GPIOD,GPIO_Pin_2);  
    RCC_APB2PeriphClockCmd(RCC_APB2Periph_GPIOC|RCC_APB2Periph_AFIO, ENABLE);  
 GPIO_PinRemapConfig(GPIO_Remap_SWJ_JTAGDisable,ENABLE);//disable JTAG  
  GPIO_InitStructure.GPIO_Pin = GPIO_Pin_0|GPIO_Pin_1|GPIO_Pin_2|GPIO_Pin_3|GPIO_Pin_4|GPIO_Pin_5|GPIO_Pin_6|GPIO_Pin_7;  
  GPIO_InitStructure.GPIO_Speed = GPIO_Speed_50MHz;  
  GPIO_InitStructure.GPIO_Mode = GPIO_Mode_Out_PP;  
  GPIO_Init(GPIOC, &GPIO_InitStructure);  
    GPIO_SetBits(GPIOC,GPIO_Pin_0|GPIO_Pin_1|GPIO_Pin_2|GPIO_Pin_3|GPIO_Pin_4|GPIO_Pin_5|GPIO_Pin_6|GPIO_Pin_7);  
      RCC_APB1PeriphClockCmd(RCC_APB1Periph_TIM2, ENABLE);  
}   
  
void USART_int(long BaudRate)  
{  
    RCC_APB2PeriphClockCmd(RCC_APB2Periph_GPIOA|RCC_APB2Periph_USART1,ENABLE);  
       GPIO_InitStructure.GPIO_Pin = GPIO_Pin_9;  
    GPIO_InitStructure.GPIO_Speed = GPIO_Speed_50MHz;  
    GPIO_InitStructure.GPIO_Mode = GPIO_Mode_AF_PP;   
    GPIO_Init(GPIOA, &GPIO_InitStructure);  
    /* PA10 USART1_Rx  */  
    GPIO_InitStructure.GPIO_Pin = GPIO_Pin_10;  
    GPIO_InitStructure.GPIO_Mode = GPIO_Mode_IN_FLOATING;  
    GPIO_Init(GPIOA, &GPIO_InitStructure);  
  /* USARTx configured as follow: 
        - BaudRate = 115200 baud   
        - Word Length = 8 Bits 
        - One Stop Bit 
        - No parity 
        - Hardware flow control disabled (RTS and CTS signals) 
        - Receive and transmit enabled 
  */  
  USART_InitStructure.USART_BaudRate = BaudRate;//??????  
  USART_InitStructure.USART_WordLength = USART_WordLength_8b;//???????8bit  
  USART_InitStructure.USART_StopBits = USART_StopBits_1;//????1  
  USART_InitStructure.USART_Parity = USART_Parity_No;//????  
  USART_InitStructure.USART_HardwareFlowControl = USART_HardwareFlowControl_None;//??????none  
  USART_InitStructure.USART_Mode = USART_Mode_Rx | USART_Mode_Tx;//??????????  
    USART_ClockInitStructure.USART_Clock = USART_Clock_Disable;       
    USART_ClockInitStructure.USART_CPOL = USART_CPOL_Low;        
    USART_ClockInitStructure.USART_CPHA = USART_CPHA_2Edge;        
    USART_ClockInitStructure.USART_LastBit = USART_LastBit_Disable;  
    USART_ClockInit(USART1, &USART_ClockInitStructure);  
  USART_Init(USART1, &USART_InitStructure);  
  USART_Cmd(USART1, ENABLE);  
    USART_ITConfig(USART1, USART_IT_RXNE, ENABLE);  
 USART_Cmd(USART1, ENABLE);  
}  
  
TestStatus Buffercmp(uint8_t* pBuffer1, uint8_t* pBuffer2, uint16_t BufferLength)  
{  
  while(BufferLength--)  
  {  
    if(*pBuffer1 != *pBuffer2)  
    {  
      return FAILED;  
    }  
  
    pBuffer1++;  
    pBuffer2++;  
  }  
  return PASSED;  
}  
  
void Delay(__IO uint32_t nCount)  
{  
  for(; nCount != 0; nCount--);  
}  
  
void ADC_CONFIG(){  
    ADC_InitTypeDef ADC_InitStructure;  
    #if defined (STM32F10X_LD_VL) || defined (STM32F10X_MD_VL) || defined (STM32F10X_HD_VL)  
  /* ADCCLK = PCLK2/2 */  
  RCC_ADCCLKConfig(RCC_PCLK2_Div2);   
#else  
  /* ADCCLK = PCLK2/4 */  
  RCC_ADCCLKConfig(RCC_PCLK2_Div4);   
#endif  
ADC_DeInit(ADC1);  
  /* Enable ADC1 and GPIOC clock */  
  RCC_APB2PeriphClockCmd(RCC_APB2Periph_ADC1 | RCC_APB2Periph_GPIOB, ENABLE);  
      
    /* Configure PB0 (ADC Channel14) as analog input -------------------------*/  
  GPIO_InitStructure.GPIO_Pin = GPIO_Pin_0;  
  GPIO_InitStructure.GPIO_Mode = GPIO_Mode_AIN;  
  GPIO_Init(GPIOB, &GPIO_InitStructure);  
      
    
  /* ADC1 configuration ------------------------------------------------------*/  
  ADC_InitStructure.ADC_Mode = ADC_Mode_Independent;  
  ADC_InitStructure.ADC_ScanConvMode = ENABLE;  
  ADC_InitStructure.ADC_ContinuousConvMode = ENABLE;  
  ADC_InitStructure.ADC_ExternalTrigConv = ADC_ExternalTrigConv_None;  
  ADC_InitStructure.ADC_DataAlign = ADC_DataAlign_Right;  
  ADC_InitStructure.ADC_NbrOfChannel = 1;  
  ADC_Init(ADC1, &ADC_InitStructure);  
  
  
  /* Enable ADC1 DMA */  
  ADC_DMACmd(ADC1, ENABLE);  
    
  /* Enable ADC1 */  
  ADC_Cmd(ADC1, ENABLE);  
  
}  
  
int Get_ADC(){  
     /* ADC1 regular channel configuration */   
  ADC_RegularChannelConfig(ADC1, ADC_Channel_8, 1, ADC_SampleTime_55Cycles5);  
    /* Enable ADC1 reset calibration register */     
  ADC_ResetCalibration(ADC1);  
  /* Check the end of ADC1 reset calibration register */  
  while(ADC_GetResetCalibrationStatus(ADC1));  
  
  /* Start ADC1 calibration */  
  ADC_StartCalibration(ADC1);  
  /* Check the end of ADC1 calibration */  
  while(ADC_GetCalibrationStatus(ADC1));  
       
  /* Start ADC1 Software Conversion */   
  ADC_SoftwareStartConvCmd(ADC1, ENABLE);  
      
    return ADC_GetConversionValue(ADC1);  
}  
  
  
void SPI_TEST()  
{  
    printf("\r\n这是一个2M SPI总线flash(W25X16)测试 \r\n");  
    SPI_FLASH_Init();  
    /* Get SPI Flash Device ID */  
    DeviceID = SPI_FLASH_ReadDeviceID();  
    Delay( 200 );  
    /* Get SPI Flash ID */  
    FlashID = SPI_FLASH_ReadID();  
    printf("\r\n FlashID is 0x%X,  Manufacturer Device ID is 0x%X\r\n", FlashID, DeviceID);  
    /* Check the SPI Flash ID */  
    if (FlashID == sFLASH_ID)  /* #define  sFLASH_ID  0xEF3015 */  
    {  
        printf("\r\n 检测到华邦flash W25X16 !\r\n");  
        /* Erase SPI FLASH Sector to write on */  
        SPI_FLASH_SectorErase(FLASH_SectorToErase);        
          
        /*写缓存并发送*/  
        SPI_FLASH_BufferWrite(Tx_Buffer, FLASH_WriteAddress, BufferSize);  
        printf("\r\n写入的数据是:%s \r\t", Tx_Buffer);  
          
        /* 读出刚才写入的数据*/  
        SPI_FLASH_BufferRead(Rx_Buffer, FLASH_ReadAddress, BufferSize);  
        printf("\r\n读出的数据是:%s \r\n", Rx_Buffer);  
          
        /* ????????????????? */  
        TransferStatus1 = Buffercmp(Tx_Buffer, Rx_Buffer, BufferSize);  
          
        if( PASSED == TransferStatus1 )  
        {      
            printf("\r\n 2M SPI总线flash(W25X16)测试成功!\n\r");  
        }  
        else  
        {          
            printf("\r\n 2M SPI总线flash(W25X16)测试失败!\n\r");  
        }  
    }// if (FlashID == sFLASH_ID)  
    else  
    {      
        printf("\r\n 未检测到 W25X16 ID!\n\r");  
    }  
      
    SPI_Flash_PowerDown();    
    printf("\r\n=================================================\n\r");  
}  
/* Private functions ---------------------------------------------------------*/  
  
/** 
  * @brief  Main program. 
  * @param  None 
  * @retval None 
  */  
int main(void)  
{  
          
  /*!< At this stage the microcontroller clock setting is already configured,  
       this is done through SystemInit() function which is called from startup 
       file (startup_stm32f10x_xx.s) before to branch to application main. 
       To reconfigure the default setting of SystemInit() function, refer to 
       system_stm32f10x.c file 
     */       
         
  /* System Clocks Configuration */  
    int i=0;  
    int AD = 0;  
     char Buffer[100];  
  RCC_Configuration();  
  USART_int(115200);  
 printf(" config done...\r\n");  
    ADC_CONFIG();  
    delay_ms(1000);  
    while(1)  
    {  
          
        for(i=0;i<5;i++)  
        {   
              ADValue = Get_ADC();  
              int_to_string(AD,Buffer);  
            Tx_Buffer[i]=Buffer[i];  
    }  
      SPI_TEST();  
        delay_ms(1000);  
    }  
}  
  
  
  
  
#ifdef  USE_FULL_ASSERT  
  
/** 
  * @brief  Reports the name of the source file and the source line number 
  *         where the assert_param error has occurred. 
  * @param  file: pointer to the source file name 
  * @param  line: assert_param error line source number 
  * @retval None 
  */  
void assert_failed(uint8_t* file, uint32_t line)  
{   
  /* User can add his own implementation to report the file name and line number, 
     ex: printf("Wrong parameters value: file %s on line %d\r\n", file, line) */  
  
  /* Infinite loop */  
  while (1)  
  {  
  }  
}  
  
#endif  
  
/** 
  * @} 
  */   
  
/** 
  * @} 
  */   
  
#ifdef __GNUC__  
  /* With GCC/RAISONANCE, small printf (option LD Linker->Libraries->Small printf 
     set to 'Yes') calls __io_putchar() */  
  #define PUTCHAR_PROTOTYPE int __io_putchar(int ch)  
#else  
  #define PUTCHAR_PROTOTYPE int fputc(int ch, FILE *f)  
#endif /* __GNUC__ */  
    
  
  
/** 
  * @brief  Retargets the C library printf function to the USART. 
  * @param  None 
  * @retval None 
  */  
PUTCHAR_PROTOTYPE  
{  
  /* Place your implementation of fputc here */  
  /* e.g. write a character to the USART */  
  USART_SendData(EVAL_COM1, (uint8_t) ch);  
  
  /* Loop until the end of transmission */  
  while (USART_GetFlagStatus(EVAL_COM1, USART_FLAG_TC) == RESET)  
  {}  
  
  return ch;  
}  
  
#ifdef  USE_FULL_ASSERT  
  
/** 
  * @brief  Reports the name of the source file and the source line number 
  *         where the assert_param error has occurred. 
  * @param  file: pointer to the source file name 
  * @param  line: assert_param error line source number 
  * @retval None 
  */  
void assert_failed(uint8_t* file, uint32_t line)  
{   
  /* User can add his own implementation to report the file name and line number, 
     ex: printf("Wrong parameters value: file %s on line %d\r\n", file, line) */  
  
  /* Infinite loop */  
  while (1)  
  {  
  }  
}  
  
#endif  
  
/******************* (C) COPYRIGHT 2011 STMicroelectronics *****END OF FILE****/