共2条
1/1 1 跳转至页
design,of,current,mirror a design of current mirror
问
Given:
Vcc = 3.6V, Iref = 1uA
Design Goal:
To obtain a 10uA output current to drive the Rload. The Rload CAN change from 10 ohms to 300K ohms. With the variation of Rload, the output current need to be maintained in 10uA with the variation of less than +/- 5%.
答 1: a design of current mirrorthis is the current
how to continnue to do it
Given:
Vcc = 3.6V, Iref = 1uA
Design Goal:
To obtain a 10uA output current to drive the Rload. The Rload CAN change from 10 ohms to 300K ohms. With the variation of Rload, the output current need to be maintained in 10uA with the variation of less than +/- 5%.
答 2: 要求帮助？3.6V/0.3MΩ=12μA
电源电压太低，作为电流输出而言，我觉得不太可能满足你10μA的要求。
不知道理解错了没有？
Vcc = 3.6V, Iref = 1uA
Design Goal:
To obtain a 10uA output current to drive the Rload. The Rload CAN change from 10 ohms to 300K ohms. With the variation of Rload, the output current need to be maintained in 10uA with the variation of less than +/- 5%.
答 1: a design of current mirrorthis is the current
how to continnue to do it
Given:
Vcc = 3.6V, Iref = 1uA
Design Goal:
To obtain a 10uA output current to drive the Rload. The Rload CAN change from 10 ohms to 300K ohms. With the variation of Rload, the output current need to be maintained in 10uA with the variation of less than +/- 5%.
答 2: 要求帮助？3.6V/0.3MΩ=12μA
电源电压太低，作为电流输出而言，我觉得不太可能满足你10μA的要求。
不知道理解错了没有？
共2条
1/1 1 跳转至页
回复
 我要赚赏金打赏帖 |
|
|---|---|
| 28BYJ-48机械臂实现人脸跟随被打赏￥24元 | |
| 基于RK3506B的片温识读功能的实现被打赏￥25元 | |
| 【瑞萨RA8D1测评】基于FreeRTOS的lvgl移植教程被打赏￥29元 | |
| 电子价签墨水屏开发被打赏￥35元 | |
| 【Ozone】RTT 打印终端使用被打赏￥29元 | |
| BMS保护板绝缘检测功能-不平衡电桥技术绝缘电阻检测设计与实现被打赏￥34元 | |
| 给28BYJ-48三自由度机械臂加一个网页控制台被打赏￥32元 | |
| 用28BYJ-48电机从零搭一台三自由度机械臂被打赏￥33元 | |
| 【英飞凌开发经验】ModusToolbox配置EdgeTalk外设被打赏￥27元 | |
| 基于BQ76952PFBR的BMS保护板热插拔损坏的原因和处理措施被打赏￥32元 | |
STM32
MCU
通讯及无线技术
物联网技术
电子DIY
板卡试用
基础知识
软件与操作系统
我爱生活
小e食堂
