共2条
1/1 1 跳转至页
design,of,current,mirror a design of current mirror
问
Given:
Vcc = 3.6V, Iref = 1uA
Design Goal:
To obtain a 10uA output current to drive the Rload. The Rload CAN change from 10 ohms to 300K ohms. With the variation of Rload, the output current need to be maintained in 10uA with the variation of less than +/- 5%.
答 1: a design of current mirrorthis is the current
how to continnue to do it
Given:
Vcc = 3.6V, Iref = 1uA
Design Goal:
To obtain a 10uA output current to drive the Rload. The Rload CAN change from 10 ohms to 300K ohms. With the variation of Rload, the output current need to be maintained in 10uA with the variation of less than +/- 5%.
答 2: 要求帮助？3.6V/0.3MΩ=12μA
电源电压太低，作为电流输出而言，我觉得不太可能满足你10μA的要求。
不知道理解错了没有？
Vcc = 3.6V, Iref = 1uA
Design Goal:
To obtain a 10uA output current to drive the Rload. The Rload CAN change from 10 ohms to 300K ohms. With the variation of Rload, the output current need to be maintained in 10uA with the variation of less than +/- 5%.
答 1: a design of current mirrorthis is the current
how to continnue to do it
Given:
Vcc = 3.6V, Iref = 1uA
Design Goal:
To obtain a 10uA output current to drive the Rload. The Rload CAN change from 10 ohms to 300K ohms. With the variation of Rload, the output current need to be maintained in 10uA with the variation of less than +/- 5%.
答 2: 要求帮助？3.6V/0.3MΩ=12μA
电源电压太低，作为电流输出而言，我觉得不太可能满足你10μA的要求。
不知道理解错了没有？
共2条
1/1 1 跳转至页
回复
| 打赏帖 | |
|---|---|
| 我踩过的那些坑之混合OTL功放与落地音箱被打赏50分 | |
| 汽车电子中巡航控制系统的使用被打赏10分 | |
| 【我踩过的那些坑】工作那些年踩过的记忆深刻的坑被打赏100分 | |
| 分享汽车电子中巡航控制系统知识被打赏10分 | |
| 分享安全气囊系统的检修注意事项被打赏10分 | |
| 分享电子控制安全气囊计算机知识点被打赏10分 | |
| 【分享开发笔记，赚取电动螺丝刀】【OZONE】使用方法总结被打赏20分 | |
| 【分享开发笔记，赚取电动螺丝刀】【S32K314】芯片启动流程分析被打赏40分 | |
| 【分享开发笔记，赚取电动螺丝刀】【S32K146】S32DS RTD 驱动环境搭建被打赏12分 | |
| 【分享开发笔记，赚取电动螺丝刀】【IAR】libc标注库time相关库函数使用被打赏23分 | |
STM32
MCU
通讯及无线技术
物联网技术
电子DIY
板卡试用
基础知识
软件与操作系统
我爱生活
小e食堂
