28335进入中断后给片选空间赋值-电子产品世界论坛

28335进入中断后给片选空间赋值

助工

2013-09-17 15:28:20 打赏

求助：
主要代码如下，为什么我把 *ExRamStart=i 注释掉之后就可以进入中断函数，可以仿真运行，LED闪烁正常；而未注释掉就不能进入中断函数了，仿真运行时软件卡死？

Uint16 *ExRamStart = (Uint16 *)0x274000;//操作地址
Uint16 i=0x00; //变量

interrupt void ISRTimer0(void) //定时器0中断函数
{
CpuTimer0.InterruptCount++;
PieCtrlRegs.PIEACK.all = PIEACK_GROUP1;
CpuTimer0Regs.TCR.bit.TIF=1;
CpuTimer0Regs.TCR.bit.TRB=1;

LED1=~LED1; //指示灯



i++;
if(i==0x3f)
{
i=0x00;
}

// *ExRamStart=i; // 在这个地址中写入变量i

}

0

关键词： 28335 中断

TLZme

助工

2013-09-17 15:52:26 打赏

2楼

求指教……

TLZme

助工

2013-09-17 15:53:09 打赏

3楼

Help……

paradoxfx

高工

2013-09-17 17:52:10 打赏

4楼

有没有初始化xintf？

TLZme

助工

2013-09-17 18:06:02 打赏

5楼

这样定义的，你帮我看一下有问题没

void InitXintf16Gpio()

{
EALLOW;
GpioCtrlRegs.GPCMUX1.bit.GPIO64 = 3; // XD15
GpioCtrlRegs.GPCMUX1.bit.GPIO65 = 3; // XD14
GpioCtrlRegs.GPCMUX1.bit.GPIO66 = 3; // XD13
GpioCtrlRegs.GPCMUX1.bit.GPIO67 = 3; // XD12
GpioCtrlRegs.GPCMUX1.bit.GPIO68 = 3; // XD11
GpioCtrlRegs.GPCMUX1.bit.GPIO69 = 3; // XD10
GpioCtrlRegs.GPCMUX1.bit.GPIO70 = 3; // XD19
GpioCtrlRegs.GPCMUX1.bit.GPIO71 = 3; // XD8
GpioCtrlRegs.GPCMUX1.bit.GPIO72 = 3; // XD7
GpioCtrlRegs.GPCMUX1.bit.GPIO73 = 3; // XD6
GpioCtrlRegs.GPCMUX1.bit.GPIO74 = 3; // XD5
GpioCtrlRegs.GPCMUX1.bit.GPIO75 = 3; // XD4
GpioCtrlRegs.GPCMUX1.bit.GPIO76 = 3; // XD3
GpioCtrlRegs.GPCMUX1.bit.GPIO77 = 3; // XD2
GpioCtrlRegs.GPCMUX1.bit.GPIO78 = 3; // XD1
GpioCtrlRegs.GPCMUX1.bit.GPIO79 = 3; // XD0

GpioCtrlRegs.GPBMUX1.bit.GPIO40 = 3; // XA0
GpioCtrlRegs.GPBMUX1.bit.GPIO41 = 3; // XA1
GpioCtrlRegs.GPBMUX1.bit.GPIO42 = 3; // XA2
GpioCtrlRegs.GPBMUX1.bit.GPIO43 = 3; // XA3
GpioCtrlRegs.GPBMUX1.bit.GPIO44 = 3; // XA4
GpioCtrlRegs.GPBMUX1.bit.GPIO45 = 3; // XA5
GpioCtrlRegs.GPBMUX1.bit.GPIO46 = 3; // XA6
GpioCtrlRegs.GPBMUX1.bit.GPIO47 = 3; // XA7
GpioCtrlRegs.GPCMUX2.bit.GPIO80 = 3; // XA8
GpioCtrlRegs.GPCMUX2.bit.GPIO81 = 3; // XA9
GpioCtrlRegs.GPCMUX2.bit.GPIO82 = 3; // XA10
GpioCtrlRegs.GPCMUX2.bit.GPIO83 = 3; // XA11
GpioCtrlRegs.GPCMUX2.bit.GPIO84 = 3; // XA12
GpioCtrlRegs.GPCMUX2.bit.GPIO85 = 3; // XA13
GpioCtrlRegs.GPCMUX2.bit.GPIO86 = 3; // XA14
GpioCtrlRegs.GPCMUX2.bit.GPIO87 = 3; // XA15
GpioCtrlRegs.GPBMUX1.bit.GPIO39 = 3; // XA16
GpioCtrlRegs.GPAMUX2.bit.GPIO31 = 3; // XA17
GpioCtrlRegs.GPAMUX2.bit.GPIO30 = 3; // XA18
GpioCtrlRegs.GPAMUX2.bit.GPIO29 = 3; // XA19

GpioCtrlRegs.GPBMUX1.bit.GPIO34 = 3; // XREADY
GpioCtrlRegs.GPBMUX1.bit.GPIO35 = 3; // XRNW
GpioCtrlRegs.GPBMUX1.bit.GPIO38 = 3; // XWE0

GpioCtrlRegs.GPBMUX1.bit.GPIO37 = 3; // XZCS7

EDIS;
}

TLZme

助工

2013-09-17 18:06:47 打赏

6楼

这样定义的，你帮我看一下有问题没

void InitXintf16Gpio()

{
EALLOW;
GpioCtrlRegs.GPCMUX1.bit.GPIO64 = 3; // XD15
GpioCtrlRegs.GPCMUX1.bit.GPIO65 = 3; // XD14
GpioCtrlRegs.GPCMUX1.bit.GPIO66 = 3; // XD13
GpioCtrlRegs.GPCMUX1.bit.GPIO67 = 3; // XD12
GpioCtrlRegs.GPCMUX1.bit.GPIO68 = 3; // XD11
GpioCtrlRegs.GPCMUX1.bit.GPIO69 = 3; // XD10
GpioCtrlRegs.GPCMUX1.bit.GPIO70 = 3; // XD19
GpioCtrlRegs.GPCMUX1.bit.GPIO71 = 3; // XD8
GpioCtrlRegs.GPCMUX1.bit.GPIO72 = 3; // XD7
GpioCtrlRegs.GPCMUX1.bit.GPIO73 = 3; // XD6
GpioCtrlRegs.GPCMUX1.bit.GPIO74 = 3; // XD5
GpioCtrlRegs.GPCMUX1.bit.GPIO75 = 3; // XD4
GpioCtrlRegs.GPCMUX1.bit.GPIO76 = 3; // XD3
GpioCtrlRegs.GPCMUX1.bit.GPIO77 = 3; // XD2
GpioCtrlRegs.GPCMUX1.bit.GPIO78 = 3; // XD1
GpioCtrlRegs.GPCMUX1.bit.GPIO79 = 3; // XD0

GpioCtrlRegs.GPBMUX1.bit.GPIO40 = 3; // XA0
GpioCtrlRegs.GPBMUX1.bit.GPIO41 = 3; // XA1
GpioCtrlRegs.GPBMUX1.bit.GPIO42 = 3; // XA2
GpioCtrlRegs.GPBMUX1.bit.GPIO43 = 3; // XA3
GpioCtrlRegs.GPBMUX1.bit.GPIO44 = 3; // XA4
GpioCtrlRegs.GPBMUX1.bit.GPIO45 = 3; // XA5
GpioCtrlRegs.GPBMUX1.bit.GPIO46 = 3; // XA6
GpioCtrlRegs.GPBMUX1.bit.GPIO47 = 3; // XA7
GpioCtrlRegs.GPCMUX2.bit.GPIO80 = 3; // XA8
GpioCtrlRegs.GPCMUX2.bit.GPIO81 = 3; // XA9
GpioCtrlRegs.GPCMUX2.bit.GPIO82 = 3; // XA10
GpioCtrlRegs.GPCMUX2.bit.GPIO83 = 3; // XA11
GpioCtrlRegs.GPCMUX2.bit.GPIO84 = 3; // XA12
GpioCtrlRegs.GPCMUX2.bit.GPIO85 = 3; // XA13
GpioCtrlRegs.GPCMUX2.bit.GPIO86 = 3; // XA14
GpioCtrlRegs.GPCMUX2.bit.GPIO87 = 3; // XA15
GpioCtrlRegs.GPBMUX1.bit.GPIO39 = 3; // XA16
GpioCtrlRegs.GPAMUX2.bit.GPIO31 = 3; // XA17
GpioCtrlRegs.GPAMUX2.bit.GPIO30 = 3; // XA18
GpioCtrlRegs.GPAMUX2.bit.GPIO29 = 3; // XA19

GpioCtrlRegs.GPBMUX1.bit.GPIO34 = 3; // XREADY
GpioCtrlRegs.GPBMUX1.bit.GPIO35 = 3; // XRNW
GpioCtrlRegs.GPBMUX1.bit.GPIO38 = 3; // XWE0

GpioCtrlRegs.GPBMUX1.bit.GPIO37 = 3; // XZCS7

EDIS;
}

TLZme

助工

2013-09-17 18:18:43 打赏

7楼

这个也试了，还是不行

void InitXintf(void)

{
// This shows how to write to the XINTF registers. The
// values used here are the default state after reset.
// Different hardware will require a different configuration.

// For an example of an XINTF configuration used with the
// F28335 eZdsp, refer to the examples/run_from_xintf project.

// Any changes to XINTF timing should only be made by code
// running outside of the XINTF.

// All Zones---------------------------------
// Timing for all zones based on XTIMCLK = 1/2 SYSCLKOUT
EALLOW;
XintfRegs.XINTCNF2.bit.XTIMCLK = 1;
// No write buffering
XintfRegs.XINTCNF2.bit.WRBUFF = 0;
// XCLKOUT is enabled
XintfRegs.XINTCNF2.bit.CLKOFF = 0;
// XCLKOUT = XTIMCLK/2
XintfRegs.XINTCNF2.bit.CLKMODE = 1;

// Zone 0------------------------------------
// When using ready, ACTIVE must be 1 or greater
// Lead must always be 1 or greater
// Zone write timing
XintfRegs.XTIMING0.bit.XWRLEAD = 3;
XintfRegs.XTIMING0.bit.XWRACTIVE = 7;
XintfRegs.XTIMING0.bit.XWRTRAIL = 3;
// Zone read timing
XintfRegs.XTIMING0.bit.XRDLEAD = 3;
XintfRegs.XTIMING0.bit.XRDACTIVE = 7;
XintfRegs.XTIMING0.bit.XRDTRAIL = 3;

// double all Zone read/write lead/active/trail timing
XintfRegs.XTIMING0.bit.X2TIMING = 1;

// Zone will sample XREADY signal
XintfRegs.XTIMING0.bit.USEREADY = 1;
XintfRegs.XTIMING0.bit.READYMODE = 1; // sample asynchronous

// Size must be either:
// 0,1 = x32 or
// 1,1 = x16 other values are reserved
XintfRegs.XTIMING0.bit.XSIZE = 3;

// Zone 6------------------------------------
// When using ready, ACTIVE must be 1 or greater
// Lead must always be 1 or greater
// Zone write timing
XintfRegs.XTIMING6.bit.XWRLEAD = 3;
XintfRegs.XTIMING6.bit.XWRACTIVE = 7;
XintfRegs.XTIMING6.bit.XWRTRAIL = 3;
// Zone read timing
XintfRegs.XTIMING6.bit.XRDLEAD = 3;
XintfRegs.XTIMING6.bit.XRDACTIVE = 7;
XintfRegs.XTIMING6.bit.XRDTRAIL = 3;

// double all Zone read/write lead/active/trail timing
XintfRegs.XTIMING6.bit.X2TIMING = 1;

// Zone will sample XREADY signal
XintfRegs.XTIMING6.bit.USEREADY = 1;
XintfRegs.XTIMING6.bit.READYMODE = 1; // sample asynchronous

// Size must be either:
// 0,1 = x32 or
// 1,1 = x16 other values are reserved
XintfRegs.XTIMING6.bit.XSIZE = 3;

// Zone 7------------------------------------
// When using ready, ACTIVE must be 1 or greater
// Lead must always be 1 or greater
// Zone write timing
XintfRegs.XTIMING7.bit.XWRLEAD = 3;
XintfRegs.XTIMING7.bit.XWRACTIVE = 7;
XintfRegs.XTIMING7.bit.XWRTRAIL = 3;
// Zone read timing
XintfRegs.XTIMING7.bit.XRDLEAD = 3;
XintfRegs.XTIMING7.bit.XRDACTIVE = 7;
XintfRegs.XTIMING7.bit.XRDTRAIL = 3;

// double all Zone read/write lead/active/trail timing
XintfRegs.XTIMING7.bit.X2TIMING = 1;

// Zone will sample XREADY signal
XintfRegs.XTIMING7.bit.USEREADY = 1;
XintfRegs.XTIMING7.bit.READYMODE = 1; // sample asynchronous

// Size must be either:
// 0,1 = x32 or
// 1,1 = x16 other values are reserved
XintfRegs.XTIMING7.bit.XSIZE = 3;

// Bank switching
// Assume Zone 7 is slow, so add additional BCYC cycles
// when ever switching from Zone 7 to another Zone.
// This will help avoid bus contention.
XintfRegs.XBANK.bit.BANK = 7;
XintfRegs.XBANK.bit.BCYC = 7;
EDIS;
//Force a pipeline flush to ensure that the write to
//the last register configured occurs before returning.

InitXintf16Gpio();
// InitXintf32Gpio();

asm(" RPT #7 || NOP");

}

paradoxfx

高工

2013-09-17 20:15:37 打赏

8楼

那cmd文件里面，zone7定义了吗

TLZme

助工

2013-09-17 20:47:38 打赏

9楼

page0里是 ZONE7A : origin = 0x200000, length = 0x00FC00

page1里是 ZONE7B : origin = 0x20FC00, length = 0x000400

这些长度加一起也不到 0x274000 吧

paradoxfx

高工

2013-09-17 21:46:57 打赏

10楼

片外的芯片是多大容量？

要么改cmd，要么把指针指到zone7A和7B以内的空间，再运行看看？

有奖活动
请大声喊出：我要开发板！
【有奖活动】EEPW网站征稿正在进行时，欢迎踊跃投稿啦
【有奖活动】智能可穿戴设备AR/VR如何引领科技新潮流！
奖！发布技术笔记，技术评测贴换取您心仪的礼品
【有奖活动】震撼来袭！这场直播将直击工程师的心灵！

打赏帖
如何实现基于NXPiMX.RT1021的BH1730采集被打赏50分
【换取手持数字示波器】AHT10温度检测分享被打赏40分
【换取手持数字示波器】ACM32F070开发板点亮LCD屏和触控按键，串口，ADC被打赏40分
【换取手持数字示波器】ACM32F070LCD屏和触控按键功驱动蜂鸣器分享被打赏40分
【换取手持数字示波器】国民技术PWM功能知识分享被打赏40分
【换取手持数字示波器】放大器运放知识分享被打赏40分
【分享评测，赢取加热台】+开关电源AC输入知识分享被打赏30分
【换取手持数字示波器】N32G430点亮数码管与串口打印、ADC被打赏40分
老胖子聊电路--分析一个反馈电路被打赏50分
【换取手持数字示波器】+点亮WS2812RGB灯被打赏50分

热门分类
STM32	MCU
通讯及无线技术	物联网技术
电子DIY	板卡试用
基础知识	软件与操作系统
我爱生活	小e食堂

EEPW论坛

28335进入中断后给片选空间赋值

回复