共1条
1/1 1 跳转至页
VT100终端编码

ASCII Character Set (Nonprinting)
7 BEL (Bell)
8 BS (Backspace)
9 HT (Horizontal tab)
10 LF (Linefeed)
11 VT (Vertical tab)
12 NP (New Page or Formfeed (FF))
13 CR (Carriage Return)
27 ESC (Escape)
127 DEL (Delete)
VT220 user defined graphics is at: http://kipper.york.ac.uk/vt220udg.html
VT404 Control Characters
Note: The "^" character signifies holding down the control key. For ^G
this is the same as sending 0x8 (a G with bit 7,8 set to zero)
Bell - ^G
Back Space - ^H
Line Feed - ^J
Reverse Line Feed - ^Z
Cursor Return - ^M
Cursor Up - ^Z
Cursor Down - ^J
Cursor Right - ^U
Cursor Left - ^H
Cursor Home - ^Y
Home and Clear - ^X
Clear to End of Line - ^V
Clear to End of Screen - ^W
Read Cursor Address - ^-
Read Character at Cursor - ^N J
Address Lead In - ^P
Address Order Row Column
Type of Addressing Bin.Bin.
*************************************
Cursor On - ^N N
Cursor Off - ^N O
VT100 Terminal Codes
--------------------
All sequences must follow the escape character immediately and all cases must be as shown.
Moving the Cursor
n,r,c are numbers.
[nA - Up, no scroll.
[nB - Down, no scroll.
[nC - Right n columns.
[nD - Left n columns.
[nE - CR and down, no scroll.
[nF - CR and up, no scroll.
[nG - CR
[r;cH - Move to row r, column c.
[nI - Tab
[nL - Inserts a blank line at cursor.
[n` - Moves cursor to column n.
D - Down, scroll in region.
E - CR and cursor down (with scroll)
M - Up, scroll in region (see later).
7 - Save position and attributes.
8 - Restore position and attributes.
Display Characteristics
[0m - Normal (default).
[1m - Bold.
[2m - Dim mode
[4m - Underline.
[5m - Blinking.
[7m - Reverse video.
[8m - Invisible mode.
#3 - Double height, double width (top).
#4 - Double height, double width (bottom).
#: - Double height, single width (top).
#; - Double height, single width (bottom).
#5 - Single width (default).
#6 - Double width.
Erasing
[0K - From cursor to end of line.
[1K - From beginning of line to cursor.
[2K - Entire line.
[0J - From cursor to bottom of screen.
[1J - From top of screen to cursor.
[2J - Entire screen.
[M - Removes the line that the cursor is on.
Character Sets
(B - US (default).
(A - UK (shift 3 = pound).
(0 - Line graphics.
(1 - Other graphics.
(S - User defined graphics.
n - First half of char. set to same as second.
N - Same as n but for next char only.
P1;n;1;5{S - Starts definition of UDGs at character code n+32.
\ - Ends definition of UDGs.
Scrolling regions
t,b are numbers.
[t;br - define scrolling region.
[?6h - cursor position 0;0 is upper left of region.
[?6l - cursor position 0;0 is upper left of screen. (Default)
Terminal Operations
c - Resets terminal.
[3h - Display controls mode.
[30h - Invisible screen.
[30l - Visible screen.
[?1h - Application keypad.
[?1l - Normal keypad.
[?2l - VT52 mode.
[?3h - 132 Columns.
[?3l - 80 Columns.
[?4h - Smooth-4 scroll.
[?4l - Jump scroll.
[?5h - Light screen.
[?5l - Dark screen.
[?25l - Cursor off.
[?25h - Cursor on.
关键词: VT100 终端 编码
共1条
1/1 1 跳转至页
回复
有奖活动 | |
---|---|
发原创文章 【每月瓜分千元赏金 凭实力攒钱买好礼~】 | |
【EEPW在线】E起听工程师的声音! | |
“我踩过的那些坑”主题活动——第001期 | |
高校联络员开始招募啦!有惊喜!! | |
【工程师专属福利】每天30秒,积分轻松拿!EEPW宠粉打卡计划启动! | |
送您一块开发板,2025年“我要开发板活动”又开始了! | |
打赏了!打赏了!打赏了! |
打赏帖 | |
---|---|
【我踩过的那些坑】电感选型错误导致的处理器连接不上被打赏50分 | |
【我踩过的那些坑】工作那些年踩过的记忆深刻的坑被打赏10分 | |
【我踩过的那些坑】DRC使用位置错误导致的问题被打赏100分 | |
我踩过的那些坑之混合OTL功放与落地音箱被打赏50分 | |
汽车电子中巡航控制系统的使用被打赏10分 | |
【我踩过的那些坑】工作那些年踩过的记忆深刻的坑被打赏100分 | |
分享汽车电子中巡航控制系统知识被打赏10分 | |
分享安全气囊系统的检修注意事项被打赏10分 | |
分享电子控制安全气囊计算机知识点被打赏10分 | |
【分享开发笔记,赚取电动螺丝刀】【OZONE】使用方法总结被打赏20分 |