作业一：Keil的安装：http://forum.eepw.com.cn/thread/277263/1#2
作业二：流水灯：http://forum.eepw.com.cn/thread/277590/1#3
作业三：0~99按键计数：http://forum.eepw.com.cn/thread/277771/1#4
作业四：双号uart控制LED流水灯转速：http://forum.eepw.com.cn/thread/277772/1#5
作业五：定时器控制LED灯：http://forum.eepw.com.cn/thread/278218/1#6
作业六：计算机开机次数：http://forum.eepw.com.cn/thread/279078/1#7
作业七：DS18B20温度使灯的颜色变化：http://forum.eepw.com.cn/thread/279079/1#8
【11.9更新】34 不熟练的流水灯作业
作业二：流水灯
#include "stm32f10x.h"
#include "stm32_eval.h"
GPIO_InitTypeDef GPIO_InitStructure;
void RCC_Configuration(void)
{
RCC_DeInit();
RCC_HSICmd(ENABLE);
while(RCC_GetFlagStatus(RCC_FLAG_HSIRDY) == RESET);
RCC_SYSCLKConfig(RCC_SYSCLKSource_HSI);
RCC_HSEConfig(RCC_HSE_OFF);
RCC_LSEConfig(RCC_LSE_OFF);
RCC_PLLConfig(RCC_PLLSource_HSI_Div2,RCC_PLLMul_9); // 72HMz
RCC_PLLCmd(ENABLE);
while(RCC_GetFlagStatus(RCC_FLAG_PLLRDY) == RESET);
RCC_ADCCLKConfig(RCC_PCLK2_Div4);
RCC_PCLK2Config(RCC_HCLK_Div1);
RCC_PCLK1Config(RCC_HCLK_Div2);
RCC_HCLKConfig(RCC_SYSCLK_Div1);
RCC_SYSCLKConfig(RCC_SYSCLKSource_PLLCLK);
while(RCC_GetSYSCLKSource() != 0x08);
RCC_APB2PeriphClockCmd(RCC_APB2Periph_GPIOD|RCC_APB2Periph_AFIO, ENABLE);
GPIO_PinRemapConfig(GPIO_Remap_SWJ_JTAGDisable,ENABLE);//disable JTAG
GPIO_InitStructure.GPIO_Pin = GPIO_Pin_2;
GPIO_InitStructure.GPIO_Speed = GPIO_Speed_50MHz;
GPIO_InitStructure.GPIO_Mode = GPIO_Mode_Out_PP;
GPIO_Init(GPIOD, &GPIO_InitStructure);
GPIO_ResetBits(GPIOD,GPIO_Pin_2);
}
void delay_us(u32 n)
{
u8 j;
while(n--)
for(j=0;j<10;j++);
}
void delay_ms(u32 n)
{
while(n--)
delay_us(1000);
}
/**
* @brief Main program.
* @param None
* @retval None
*/
int main(void)
{ unsigned char flag=0;
RCC_Configuration();
RCC_APB2PeriphClockCmd(RCC_APB2Periph_GPIOC, ENABLE);
RCC_APB2PeriphClockCmd(RCC_APB2Periph_GPIOC, ENABLE);
GPIO_InitStructure.GPIO_Pin = GPIO_Pin_8;
GPIO_InitStructure.GPIO_Speed = GPIO_Speed_50MHz;
GPIO_InitStructure.GPIO_Mode = GPIO_Mode_IN_FLOATING;
GPIO_Init(GPIOC, &GPIO_InitStructure);
GPIO_InitStructure.GPIO_Pin = GPIO_Pin_0|GPIO_Pin_1|GPIO_Pin_2|GPIO_Pin_3|GPIO_Pin_4|GPIO_Pin_5|GPIO_Pin_6|GPIO_Pin_7;
GPIO_InitStructure.GPIO_Speed = GPIO_Speed_50MHz;
GPIO_InitStructure.GPIO_Mode = GPIO_Mode_Out_PP;
GPIO_Init(GPIOC, &GPIO_InitStructure);
while(1)
{
GPIO_SetBits(GPIOC,GPIO_Pin_0);
GPIO_SetBits(GPIOC,GPIO_Pin_1);
GPIO_SetBits(GPIOC,GPIO_Pin_2);
GPIO_SetBits(GPIOC,GPIO_Pin_3);
GPIO_SetBits(GPIOC,GPIO_Pin_4);
GPIO_SetBits(GPIOC,GPIO_Pin_5);
GPIO_SetBits(GPIOC,GPIO_Pin_6);
GPIO_SetBits(GPIOC,GPIO_Pin_7);
delay_ms(100);
GPIO_ResetBits(GPIOC,GPIO_Pin_0);
delay_ms(100);
GPIO_SetBits(GPIOC,GPIO_Pin_0);
delay_ms(100);
GPIO_ResetBits(GPIOC,GPIO_Pin_1);
delay_ms(100);
GPIO_SetBits(GPIOC,GPIO_Pin_1);
delay_ms(100);
GPIO_ResetBits(GPIOC,GPIO_Pin_2);
delay_ms(100);
GPIO_SetBits(GPIOC,GPIO_Pin_2);
delay_ms(100);
GPIO_ResetBits(GPIOC,GPIO_Pin_3);
delay_ms(100);
GPIO_SetBits(GPIOC,GPIO_Pin_3);
delay_ms(100);
GPIO_ResetBits(GPIOC,GPIO_Pin_4);
delay_ms(100);
GPIO_SetBits(GPIOC,GPIO_Pin_4);
delay_ms(100);
GPIO_ResetBits(GPIOC,GPIO_Pin_5);
delay_ms(100);
GPIO_SetBits(GPIOC,GPIO_Pin_5);
delay_ms(100);
GPIO_ResetBits(GPIOC,GPIO_Pin_6);
delay_ms(100);
GPIO_SetBits(GPIOC,GPIO_Pin_6);
delay_ms(100);
GPIO_ResetBits(GPIOC,GPIO_Pin_7);
delay_ms(100);
GPIO_SetBits(GPIOC,GPIO_Pin_7);
delay_ms(100);
}
}
虽然不怎么懂，但是通过借鉴和参考还是可以完成作业的，我承认我是菜鸟，哎，没办法呀！
作业三：34号 0~99按键计数
虽然是借助大神的，还是勉强完成了！
【11.15更新】34号 双号uart控制LED流水灯转速 【没有办法的办法，你懂的】
作业四：uart控制LED流水灯转速
作业五：定时器控制LED灯
#include "stm32f10x.h"
#include "stm32_eval.h"
#include <stdio.h>
/** @addtogroup STM32F10x_StdPeriph_Examples
* @{
*/
/** @addtogroup EXTI_Config
* @{
*/
/* Private typedef -----------------------------------------------------------*/
/* Private define ------------------------------------------------------------*/
/* Private macro -------------------------------------------------------------*/
/* Private variables ---------------------------------------------------------*/
EXTI_InitTypeDef EXTI_InitStructure;
GPIO_InitTypeDef GPIO_InitStructure;
NVIC_InitTypeDef NVIC_InitStructure;
USART_InitTypeDef USART_InitStructure;
USART_ClockInitTypeDef USART_ClockInitStructure;
TIM_TimeBaseInitTypeDef TIM_TimeBaseStructure;
TIM_OCInitTypeDef TIM_OCInitStructure;
int count=0;
void RCC_Configuration(void)
{/*
RCC_DeInit();
RCC_HSICmd(ENABLE);
while(RCC_GetFlagStatus(RCC_FLAG_HSIRDY) == RESET);
RCC_SYSCLKConfig(RCC_SYSCLKSource_HSI);
RCC_HSEConfig(RCC_HSE_OFF);
RCC_LSEConfig(RCC_LSE_OFF);
RCC_PLLConfig(RCC_PLLSource_HSI_Div2,RCC_PLLMul_9); // 72HMz
RCC_PLLCmd(ENABLE);
while(RCC_GetFlagStatus(RCC_FLAG_PLLRDY) == RESET);
RCC_ADCCLKConfig(RCC_PCLK2_Div4);
RCC_PCLK2Config(RCC_HCLK_Div1);
RCC_PCLK1Config(RCC_HCLK_Div2);
RCC_HCLKConfig(RCC_SYSCLK_Div1);
RCC_SYSCLKConfig(RCC_SYSCLKSource_PLLCLK);
while(RCC_GetSYSCLKSource() != 0x08);
*/
SystemInit();
RCC_APB2PeriphClockCmd(RCC_APB2Periph_GPIOD|RCC_APB2Periph_AFIO, ENABLE);
GPIO_PinRemapConfig(GPIO_Remap_SWJ_JTAGDisable,ENABLE);//disable JTAG
RCC_APB2PeriphClockCmd(RCC_APB2Periph_GPIOD|RCC_APB2Periph_AFIO, ENABLE);
GPIO_PinRemapConfig(GPIO_Remap_SWJ_JTAGDisable,ENABLE);//disable JTAG
GPIO_InitStructure.GPIO_Pin = GPIO_Pin_2;
GPIO_InitStructure.GPIO_Speed = GPIO_Speed_50MHz;
GPIO_InitStructure.GPIO_Mode = GPIO_Mode_Out_PP;
GPIO_Init(GPIOD, &GPIO_InitStructure);
GPIO_ResetBits(GPIOD,GPIO_Pin_2);
RCC_APB2PeriphClockCmd(RCC_APB2Periph_GPIOC|RCC_APB2Periph_AFIO, ENABLE);
GPIO_PinRemapConfig(GPIO_Remap_SWJ_JTAGDisable,ENABLE);//disable JTAG
GPIO_InitStructure.GPIO_Pin = GPIO_Pin_0|GPIO_Pin_1|GPIO_Pin_2|GPIO_Pin_3|GPIO_Pin_4|GPIO_Pin_5|GPIO_Pin_6|GPIO_Pin_7;
GPIO_InitStructure.GPIO_Speed = GPIO_Speed_50MHz;
GPIO_InitStructure.GPIO_Mode = GPIO_Mode_Out_PP;
GPIO_Init(GPIOC, &GPIO_InitStructure);
GPIO_SetBits(GPIOC,GPIO_Pin_0|GPIO_Pin_1|GPIO_Pin_2|GPIO_Pin_3|GPIO_Pin_4|GPIO_Pin_5|GPIO_Pin_6|GPIO_Pin_7);
RCC_APB1PeriphClockCmd(RCC_APB1Periph_TIM2, ENABLE);
}
void USART_int(long BaudRate)
{
RCC_APB2PeriphClockCmd(RCC_APB2Periph_GPIOA|RCC_APB2Periph_USART1,ENABLE);
GPIO_InitStructure.GPIO_Pin = GPIO_Pin_9;
GPIO_InitStructure.GPIO_Speed = GPIO_Speed_10MHz;
GPIO_InitStructure.GPIO_Mode = GPIO_Mode_AF_PP;
GPIO_Init(GPIOA, &GPIO_InitStructure);
/* PA10 USART1_Rx */
GPIO_InitStructure.GPIO_Pin = GPIO_Pin_10;
GPIO_InitStructure.GPIO_Mode = GPIO_Mode_IN_FLOATING;
GPIO_Init(GPIOA, &GPIO_InitStructure);
/* USARTx configured as follow:
- BaudRate = 115200 baud
- Word Length = 8 Bits
- One Stop Bit
- No parity
- Hardware flow control disabled (RTS and CTS signals)
- Receive and transmit enabled
*/
USART_InitStructure.USART_BaudRate = BaudRate;//??????
USART_InitStructure.USART_WordLength = USART_WordLength_8b;//???????8bit
USART_InitStructure.USART_StopBits = USART_StopBits_1;//????1
USART_InitStructure.USART_Parity = USART_Parity_No;//????
USART_InitStructure.USART_HardwareFlowControl = USART_HardwareFlowControl_None;//??????none
USART_InitStructure.USART_Mode = USART_Mode_Rx | USART_Mode_Tx;//??????????
USART_ClockInitStructure.USART_Clock = USART_Clock_Disable;
USART_ClockInitStructure.USART_CPOL = USART_CPOL_Low;
USART_ClockInitStructure.USART_CPHA = USART_CPHA_2Edge;
USART_ClockInitStructure.USART_LastBit = USART_LastBit_Disable;
USART_ClockInit(USART1, &USART_ClockInitStructure);
USART_Init(USART1, &USART_InitStructure);
USART_Cmd(USART1, ENABLE);
USART_ITConfig(USART1, USART_IT_RXNE, ENABLE);
USART_Cmd(USART1, ENABLE);
}
void NVIC_Configuration(void)
{
NVIC_InitTypeDef NVIC_InitStructure;
/* Enable the TIM2 global Interrupt */
NVIC_InitStructure.NVIC_IRQChannel = TIM2_IRQn;
NVIC_InitStructure.NVIC_IRQChannelPreemptionPriority = 0;
NVIC_InitStructure.NVIC_IRQChannelSubPriority = 1;
NVIC_InitStructure.NVIC_IRQChannelCmd = ENABLE;
NVIC_Init(&NVIC_InitStructure);
}
int main(void)
{
/*!< At this stage the microcontroller clock setting is already configured,
this is done through SystemInit() function which is called from startup
file (startup_stm32f10x_xx.s) before to branch to application main.
To reconfigure the default setting of SystemInit() function, refer to
system_stm32f10x.c file
*/
/* System Clocks Configuration */
RCC_Configuration();
NVIC_Configuration();
//USART_int(115200);
// printf("config done...\r\n");
/* Time base configuration */
TIM_TimeBaseStructure.TIM_Period = 36000;
TIM_TimeBaseStructure.TIM_Prescaler = 100;
TIM_TimeBaseStructure.TIM_ClockDivision = 0;
TIM_TimeBaseStructure.TIM_CounterMode = TIM_CounterMode_Up;
TIM_TimeBaseInit(TIM2, &TIM_TimeBaseStructure);
TIM_ITConfig(TIM2,TIM_IT_Update,ENABLE );
/* TIM2 enable counter */
TIM_Cmd(TIM2, ENABLE);
while (1){
//if(flag == 1)
// {printf("TIM2 interrupt......\r\n");
//flag = 0;
}
//else{GPIO_SetBits(GPIOC,GPIO_Pin_0|GPIO_Pin_1|GPIO_Pin_2|GPIO_Pin_3|GPIO_Pin_4|GPIO_Pin_5|GPIO_Pin_6|GPIO_Pin_7);}
//}
}
void TIM2_IRQHandler(void) //TIM3
{
if (TIM_GetITStatus(TIM2, TIM_IT_Update) != RESET)
{
TIM_ClearITPendingBit(TIM2, TIM_IT_Update );
// flag = ~flag;
// if(flag){
// GPIO_SetBits(GPIOC,GPIO_Pin_1);}
// else {GPIO_ResetBits(GPIOC,GPIO_Pin_1);}
/*flag++;
if(flag == 50)
{led = ~led;
flag = 0;}
if(led){
GPIO_SetBits(GPIOC,GPIO_Pin_1);}
else {GPIO_ResetBits(GPIOC,GPIO_Pin_1);}*/
count++;
GPIO_SetBits(GPIOC,GPIO_Pin_0|GPIO_Pin_1|GPIO_Pin_2|GPIO_Pin_3|GPIO_Pin_4|GPIO_Pin_5|GPIO_Pin_6|GPIO_Pin_7);
if(count==1)
GPIO_ResetBits(GPIOC,GPIO_Pin_0);
if(count==2)
GPIO_ResetBits(GPIOC,GPIO_Pin_1);
if(count==3)
GPIO_ResetBits(GPIOC,GPIO_Pin_2);
if(count==4)
GPIO_ResetBits(GPIOC,GPIO_Pin_3);
if(count==5)
GPIO_ResetBits(GPIOC,GPIO_Pin_4);
if(count==6)
GPIO_ResetBits(GPIOC,GPIO_Pin_5);
if(count==7)
GPIO_ResetBits(GPIOC,GPIO_Pin_6);
if(count==8)
GPIO_ResetBits(GPIOC,GPIO_Pin_7);
if(count==9)
count=0;
}
}
#ifdef USE_FULL_ASSERT
/**
* @brief Reports the name of the source file and the source line number
* where the assert_param error has occurred.
* @param file: pointer to the source file name
* @param line: assert_param error line source number
* @retval None
*/
void assert_failed(uint8_t* file, uint32_t line)
{
/* User can add his own implementation to report the file name and line number,
ex: printf("Wrong parameters value: file %s on line %d\r\n", file, line) */
/* Infinite loop */
while (1)
{
}
}
#endif
#ifdef __GNUC__
/* With GCC/RAISONANCE, small printf (option LD Linker->Libraries->Small printf
set to 'Yes') calls __io_putchar() */
#define PUTCHAR_PROTOTYPE int __io_putchar(int ch)
#else
#define PUTCHAR_PROTOTYPE int fputc(int ch, FILE *f)
#endif /* __GNUC__ */
PUTCHAR_PROTOTYPE
{
/* Place your implementation of fputc here */
/* e.g. write a character to the USART */
USART_SendData(EVAL_COM1, (uint8_t) ch);
/* Loop until the end of transmission */
while (USART_GetFlagStatus(EVAL_COM1, USART_FLAG_TC) == RESET)
{}
return ch;
}
#ifdef USE_FULL_ASSERT
void assert_failed(uint8_t* file, uint32_t line)
{
/* User can add his own implementation to report the file name and line number,
ex: printf("Wrong parameters value: file %s on line %d\r\n", file, line) */
/* Infinite loop */
while (1)
{
}
}
#endif
我是菜鸟，都懂的
作业六：计算机开机次数
sfr IAP_DATA = 0xE2;
sfr IAP_ADDRH = 0xE3;
sfr IAP_ADDRL = 0xE4;
sfr IAP_CMD = 0xE5;
sfr IAP_TRIG = 0xE6;
sfr IAP_CONTR = 0xE7;
#define CMD_IDLE 0
#define CMD_READ 1
#define CMD_PROGRAM 2
#define CMD_ERASE 3
#define ENABLE_IAP0x80
#define ENABLE_IAP0x81
#define ENABLE_IAP0x82
#define ENABLE_IAP0x83
IAP_ADDRESS 0x2000 //STC90C52ϵÁÐEEPROM²âÊÔÆðʼµØÖ·
void IapIdle(void)
{
IAP_CONTR=0;
IAP_CMD =0;
IAP_TRIG =0;
IAP_ADDRH=0x80;
IAP_ADDRL =0;
}
unsigned char IapReadByte(unsigned int addt)
{
unsigned char dat;
IAP_CONTR=ENABLE_IAP;
IAP_CMD =CMD_READ;
IAP_ADDRL=addr;
IAP_ADDRL=addr>>8
IAP_TRIG =0x46;
IAP_TRIG =0xb9;
dat = IAP_DATA;
IapIdle();
return dat;
}
void Iap ProgramByte(unsigned int addr,unsigned char dat )
{
IAP_CONTR=ENABLE_IAP;
IAP_CMD =CMD_REOGRAM;
IAP_ADDRL=addr;
IAP_ADDRH=addr>>8
IAP_DATA=date;
IAP_TRIG =0x46;
IAP_TRIG =0xb9;
IapIdle();
}
void Iap EraseSector(unsigned int addr )
{
IAP_CONTR=ENABLE_IAP;
IAP_CMD =CMD_ERASE;
IAP_ADDRL=addr;
IAP_ADDRH=addr>>8
IAP_TRIG =0x46;
IAP_TRIG =0xb9;
IapIdle();
}
unsigned char Num=0;
void main(void)
{
unsigned long i=0;
Num = Iap ReadByte(IAP_ADDRESS+20);
Num++;
Iap EraseSector(IAP_ADDRESS);
Iap ProgramByte(IAP_ADDRESS+20,Num);
for(i=0;i
{
LED0=0;
DelayMs(100);
LED0=1;
DelayMs(100);
}
while(1);
}
作业七：DS18B20温度使灯的颜色变化
#define "ds18b20.h"
#define "delay.h"
#include "sys.h"
#include "usart.h"
#include "led.h"
#include "lcd.h"
void DS18B20_Rst(void)
{
DS18B20_IO_OUT(); //SET PG11 OUTPUT
DS18B20_DQ_OUT=0; //拉低 DQ
delay_us(750); //拉低 750us
DS18B20_DQ_OUT=1; //DQ=1
delay_us(15); //15US
}
//等待 DS18B20 的回应
//返回 1:未检测到 DS18B20 的存在
//返回 0:存在
u8 DS18B20_Check(void)
{
u8 retry=0;
DS18B20_IO_IN();//SET PG11 INPUT
while (DS18B20_DQ_IN&&retry<200) { retry++; delay_us(1); };
if(retry>=200)return 1;
else retry=0;
while (!DS18B20_DQ_IN&&retry<240) {retry++; delay_us(1); };
if(retry>=240)return 1;
return 0;
}
//从 DS18B20 读取一个位
//返回值：1/0
u8 DS18B20_Read_Bit(void)
{
u8 data;
DS18B20_IO_OUT();//SET PG11 OUTPUT
DS18B20_DQ_OUT=0;
delay_us(2);
DS18B20_DQ_OUT=1;
DS18B20_IO_IN();//SET PG11 INPUT
delay_us(12);
if(DS18B20_DQ_IN)data=1;
else data=0;
delay_us(50);
return data;
}
//从 DS18B20 读取一个字节
//返回值：读到的数据
u8 DS18B20_Read_Byte(void)
{
u8 i,j,dat;
dat=0;
for (i=1;i<=8;i++)
{
j=DS18B20_Read_Bit();
dat=(j<<7)|(dat>>1);
}
return dat;
}
//写一个字节到 DS18B20
//dat：要写入的字节
void DS18B20_Write_Byte(u8 dat)
{
u8 j;
u8 testb;
DS18B20_IO_OUT();//SET PG11 OUTPUT;
for (j=1;j<=8;j++)
{
testb=dat&0x01;
dat=dat>>1;
if (testb)
{
DS18B20_DQ_OUT=0;// Write 1
delay_us(2);
DS18B20_DQ_OUT=1;
delay_us(60);
}
else
{
DS18B20_DQ_OUT=0;// Write 0
delay_us(60);
DS18B20_DQ_OUT=1;
delay_us(2);
}
}
}
//开始温度转换
void DS18B20_Start(void)
{
DS18B20_Rst();
DS18B20_Check();
DS18B20_Write_Byte(0xcc);// skip rom
DS18B20_Write_Byte(0x44);// convert
}
//初始化 DS18B20 的 IO 口 DQ 同时检测 DS 的存在
//返回 1:不存在
//返回 0:存在
u8 DS18B20_Init(void)
{
GPIO_InitTypeDef GPIO_InitStructure;
RCC_AHB1PeriphClockCmd(RCC_AHB1Periph_GPIOG, ENABLE); //使能 GPIOG 时钟
//GPIOG9
GPIO_InitStructure.GPIO_Pin = GPIO_Pin_9;
GPIO_InitStructure.GPIO_Mode = GPIO_Mode_OUT; //普通输出模式
GPIO_InitStructure.GPIO_OType = GPIO_OType_PP; //推挽输出
GPIO_InitStructure.GPIO_Speed = GPIO_Speed_50MHz; //50MHz
GPIO_InitStructure.GPIO_PuPd = GPIO_PuPd_UP; //上拉
GPIO_Init(GPIOG, &GPIO_InitStructure); //初始化
DS18B20_Rst();
return DS18B20_Check();
}
//从 ds18b20 得到温度值
//精度：0.1C
//返回值：温度值 （-550~1250）
short DS18B20_Get_Temp(void)
{
u8 temp;
u8 TL,TH;
short tem;
DS18B20_Start();// ds1820 start convert
DS18B20_Rst();
DS18B20_Check();
DS18B20_Write_Byte(0xcc);// skip rom
DS18B20_Write_Byte(0xbe);// convert
TL=DS18B20_Read_Byte(); // LSB
TH=DS18B20_Read_Byte(); // MSB
if(TH>7)
{
TH=~TH;
TL=~TL;
temp=0; //温度为负
}else temp=1; //温度为正
tem=TH; //获得高八位
tem<<=8;
tem+=TL; //获得底八位
tem=(double)tem*0.625; //转换
if(temp)return tem; //返回温度值
else return -tem;
}
//ds18b20.h
#ifndef__DS18B20_H
#define__DS18B20_H
#include"sys.h"
#include"sys.h"
//IO方向设置
#define DS18B20_IO_IN() {GPIOG->MODERA=~(3<<(9*2));GPIOG->MODERA=~(0<<(9*2))} //PG9输入模式
#define DS18B20_IO_OUT() {GPIOG->MODERA=~(3<<(9*2));GPIOG->MODERA=~(0<<(9*2))} //PG9输出模式
//IO操作函数
#define DS18B20_DQ_IN PGout(9) //数据端口 PG9
#define DS18B20_DQ_OUT PGout(9) //数据端口PG9
u8 DS18B20_Init(void); //初始化DS18B20
short DS18B20_Get_Temp(void); //获取温度
void DS18B20_Start(void); //开始温度转换
void DS18B20_Write_Byte(u8 dat); //写 入一个字节
u8 DS18B20_Read_Byte(void); //读出一个字节
u8 DS18B20_Read_Bit(void); //读出一个位
u8 DS18B20_Check(void); //检测是否存在DS18B20
void DS18B20_Rst(void); //复位DS18B20
int main(void)
{
u8 t=0;
short temperature;
NVIC_PriorityGroupConfig(NVIC_PriorityGroup_2); //设置系统中断优先级分组2
delay_init(168); //初始化延时函数
uart_init(115200); //初始化串口波特率为115200
LED_Init(); //初始化LED
LCD_Init();
POINT_COLOR=RED; //设置字体为红色
LCD_ShowString(30,50,200,16,16,"Explorer STM32F4");
LCD_ShowString(30,70,200,16,16,"DS18B20 TEST");
LCD_ShowString(30,90,200,16,16,"ATOM@ALIENTEK");
LCD_ShowString(30,110,200,16,16,"2014/5/7");
while(DS18B20_Init()) //DS18B20初始化
{
LCD_ShowString(30,130,200,16,16,"DS18B20 Error");
delay_ms(200);
LCD_Fill(30,130,239,130+16,WHITE);
delay_ms(200);
}
LCD_ShowString(30,130,200,16,16,"DS18B20 OK");
POINT_COLOR=BLUE; //设置字体为蓝色
LCD_ShowString(30,150,200,16,16,"Temp: . C");
while(1)
{
if(t%10==0)//每100ms读取一次
{
temperature=DS18B20_Get_Temp();
if(temperature<0)
{
LCD_ShowChar(30+40,150,'-',16,0); //显示负号
temperature=-temperature; //转为正数
}else LCD_ShowChar(30+40,150,' ',16,0); //去掉负号
LCD_ShowNum(30+40+8,150,temperature/10,2,16); //显示正数部分
LCD_ShowNum(30+40+32,150,temperature%10,1,16); //显示小数部分
}
delay_ms(10);
t++;
if(t==20)
{
t=0;
LED0=!LED0;
}
}
}
我们这种菜鸟，没办法，很多都是借鉴参考别人的，老师你轻些！| 有奖活动 | |
|---|---|
| 【有奖活动】分享技术经验，兑换京东卡 | |
| 话不多说，快进群！ | |
| 请大声喊出：我要开发板！ | |
| 【有奖活动】EEPW网站征稿正在进行时，欢迎踊跃投稿啦 | |
| 奖！发布技术笔记，技术评测贴换取您心仪的礼品 | |
| 打赏了！打赏了！打赏了！ | |
| 打赏帖 | |
|---|---|
| 与电子爱好者谈读图四被打赏50分 | |
| 与电子爱好者谈读图二被打赏50分 | |
| 【FRDM-MCXN947评测】Core1适配运行FreeRtos被打赏50分 | |
| 【FRDM-MCXN947评测】双核调试被打赏50分 | |
| 【CPKCORRA8D1B评测】---移植CoreMark被打赏50分 | |
| 【CPKCORRA8D1B评测】---打开硬件定时器被打赏50分 | |
| 【FRDM-MCXA156评测】4、CAN loopback模式测试被打赏50分 | |
| 【CPKcorRA8D1评测】--搭建初始环境被打赏50分 | |
| 【FRDM-MCXA156评测】3、使用FlexIO模拟UART被打赏50分 | |
| 【FRDM-MCXA156评测】2、rt-thread MCXA156 BSP制作被打赏50分 | |
STM32
MCU
通讯及无线技术
物联网技术
电子DIY
板卡试用
基础知识
软件与操作系统
我爱生活
小e食堂